Bonjour, je viens de recevoir mon controleur
Adaptec (raid + sas), j'y ai mit 8hdd de 1To, avec
cfdisk je le vois:
Code :
- cfdisk (util-linux-ng 2.13.1.1)
- Disk Drive: /dev/sda
- Size: 6997564981248 bytes, 6997.5 GB
- Heads: 255 Sectors per Track: 63 Cylinders: 850738
- Name Flags Part Type FS Type [Label] Size (MB)
- -------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
- Pri/Log Free Space 6997558.26
|
Mais quand je creer une partition tout vas bien,
et quand je reviens dans cfdisk il me fait:
Code :
- cfdisk (util-linux-ng 2.13.1.1)
- Disk Drive: /dev/sda
- Size: 6997564981248 bytes, 6997.5 GB
- Heads: 255 Sectors per Track: 63 Cylinders: 850738
- Name Flags Part Type FS Type [Label] Size (MB)
- -------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
- sda1 Primary Linux ext3 400488.49 *
- Pri/Log Free Space 6597069.77 *
|
Un autre problème, je vois bien mes hdd avec
dmesg:
Code :
- AAC0: kernel 5.2-0[15738] Mar 28 2008
- AAC0: monitor 5.2-0[15738]
- AAC0: bios 5.2-0[15738]
- AAC0: serial 8B26106A81D
- AAC0: Non-DASD support enabled.
- AAC0: 64bit support enabled.
- AAC0: 64 Bit DAC enabled
- scsi0 : aacraid
- scsi 0:0:0:0: Direct-Access Adaptec all
- V1.0 PQ: 0 ANSI: 2
- scsi 0:1:0:0: Direct-Access ST31000340AS SD15 PQ: 0 ANSI: 5
- scsi 0:1:1:0: Direct-Access ST31000340AS SD15 PQ: 0 ANSI: 5
- scsi 0:1:2:0: Direct-Access ST31000340AS SD15 PQ: 0 ANSI: 5
- scsi 0:1:3:0: Direct-Access ST31000340AS SD15 PQ: 0 ANSI: 5
- scsi 0:1:4:0: Direct-Access ST31000340AS SD15 PQ: 0 ANSI: 5
- scsi 0:1:5:0: Direct-Access ST31000340AS SD15 PQ: 0 ANSI: 5
- scsi 0:1:6:0: Direct-Access ST31000340AS SD15 PQ: 0 ANSI: 5
- scsi 0:1:7:0: Direct-Access ST31000340AS SD15 PQ: 0 ANSI: 5
- Driver 'sd' needs updating - please use bus_type methods
- sd 0:0:0:0: Very big device. Trying to use READ
- CAPACITY(16).
- sd 0:0:0:0: 13667119104 512-byte hardware sectors
- (6997565 MB)
- sd 0:0:0:0: Write Protect is off
- sd 0:0:0:0: Mode Sense: 06 00 10 00
- sd 0:0:0:0: Write cache: enabled, read cache:
- enabled, supports DPO and FUA
- sd 0:0:0:0: Very big device. Trying to use READ
- CAPACITY(16).
- sd 0:0:0:0: 13667119104 512-byte hardware sectors
- (6997565 MB)
- sd 0:0:0:0: Write Protect is off
- sd 0:0:0:0: Mode Sense: 06 00 10 00
- sd 0:0:0:0: Write cache: enabled, read cache:
- enabled, supports DPO and FUA
- sda: unknown partition table
- sd 0:0:0:0: Attached SCSI removable disk
- sd 0:0:0:0: Attached scsi generic sg0 type 0
- scsi 0:1:0:0: Attached scsi generic sg1 type 0
- scsi 0:1:1:0: Attached scsi generic sg2 type 0
- scsi 0:1:2:0: Attached scsi generic sg3 type 0
- scsi 0:1:3:0: Attached scsi generic sg4 type 0
- scsi 0:1:4:0: Attached scsi generic sg5 type 0
- scsi 0:1:5:0: Attached scsi generic sg6 type 0
- scsi 0:1:6:0: Attached scsi generic sg7 type 0
- scsi 0:1:7:0: Attached scsi generic sg8 type 0
|
Mais pas moyen de mettre en veille auto aprés un certain temps les hdd:
Code :
- hdparm -S 120 /dev/sg1
- /dev/sg1:
- setting standby to 120 (10 minutes)
- HDIO_DRIVE_CMD(setidle1) failed: Inappropriate
- ioctl for device
|
Car il n'y as rien dans le bios du contrôleur qui permet de faire cela.
J'ai ça:
Code :
- Very big device. Trying to use READ CAPACITY(16).
|
Normal? C'est juste une note? Il faut en tenir compte? Car google ne m'aide pas vraiment sur ces point sur que c'est du matos hors norme.
Merci d'avance de votre aide, je débute en scsi et hdd de grande capacité.
---------------
Développeur d'Ultracopier et Supercopier 3
FORUM HardWare.fr
