prudho Euh... non rien ! | J'ai terminé mes soudure sur la CM pour avoir un accès console.
Voilà le log en boot normal : Citation :
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2011.05.05 17:01:21 =~=~=~=~=~=~=~=~=~=~=~=
Žà
U-Boot 1.3.4 (May 14 2010 - 18:09:39) for E6
CPU: S5PC100@666MHz
Fclk = 666MHz, Hclk = 166MHz, Pclk = 66MHz, DoutMpll = 133MHz, Serial = PCLK Board: E6 e-Diary
DRAM: 256 MB
Flash: 0 kB
SD/MMC: 1960MB
The input address don't need a virtual-to-physical translation : 27e7c008
Init EPD Panel.........done
In: serial
Out: serial
Err: serial
Net: No ethernet found
Hit any key to stop autoboot: 0 reading kernel.. 3996624, 8128 MMC read: dev # 0, block # 3996624, count 8128 ... 8128 blocks read: OK
completed
get_format
-------- 1 --------
## Booting kernel from Legacy Image at c0008000 ...
Image Name: Linux-2.6.29.4
Created: 2010-08-11 14:09:59 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1692744 Bytes = 1.6 MB
Load Address: 20008000
Entry Point: 20008000
Verifying Checksum ... OK
get_format
-------- 1 --------
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux.............................................................................................................. done, booting the kernel.
Linux version 2.6.29.4 (ypumpin@linux-btq8) (gcc version 4.2.2) #1 Wed Aug 11 21:47:37 KST 2010
CPU: ARMv7 Processor [412fc081] revision 1 (ARMv7), cr=10c5387f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: SNE-60K
Ignoring unrecognised tag 0x41001099
Memory policy: ECC disabled, Data cache writeback
CPU S5PC100 (id 0x43100000)
S3C24XX Clocks, (c) 2004 Simtec Electronics
S5PC100: PLL settings, A=666000000, M=267000000, E=133000000, H=24000000
S5PC100: ARMCLK=666000000, HCLKD0=166500000, PCLKD0=83250000, HCLK=133500000, PCLK=66750000
mout_apll: source is fout_apll (1), rate is 666000000
mout_epll: source is fout_epll (1), rate is 133000000
mout_mpll: source is mpll (1), rate is 267000000
mout_hpll: source is srclk (1), rate is 24000000
mmc_bus: source is dout_mpll (1), rate is 44500000
mmc_bus: source is dout_mpll (1), rate is 44500000
mmc_bus: source is dout_mpll (1), rate is 44500000
usb-host-bus: source is dout_mpll (1), rate is 133500000
uclk1: source is dout_mpll (1), rate is 66750000
spi_epll: source is dout_mpll2 (1), rate is 66750000
spi_epll: source is dout_mpll2 (1), rate is 66750000
spi_epll: source is dout_mpll2 (1), rate is 66750000
sclk_audio0: source is mout_epll (0), rate is 133000000
sclk_audio1: source is mout_epll (0), rate is 133000000
sclk_audio2: source is mout_epll (0), rate is 133000000
i2sclkd2: source is fout_epll (0), rate is 133000000
sclk_irda: source is dout_mpll (1), rate is 133500000
sclk_pwi: source is srclk (0), rate is 0
sclk_lcd: source is dout_mpll (1), rate is 133500000
sclk_fimc: source is dout_mpll (1), rate is 133500000
sclk_fimc: source is dout_mpll (1), rate is 133500000
sclk_fimc: source is dout_mpll (1), rate is 133500000
sclk_mixer: source is clk_27m (0), rate is 27000000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
Kernel command line: root=/dev/mmcblk0p1 rootfstype=squashfs init=/linuxrc console=ttySAC0,115200 mem=256M
PID hash table entries: 1024 (order: 10, 4096 bytes)
Console: colour dummy device 80x30
console [ttySAC0] enabled
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 256MB = 256MB total
Memory: 255360KB available (3076K code, 1108K data, 120K init)
SLUB: Genslabs=12, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay loop... 665.19 BogoMIPS (lpj=1662976)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 564 bytes
S5PC1XX GPIO Driver Init
NET: Registered protocol family 16
s5pc1xx Power Management, (c) 2008 Samsung Electronics
Created proc/sleep_wakeup/pm_mode Succssfully S5PC100: Initialising architecture
S3C PL330-DMA Controller Driver, (c) 2008-2009 Samsung Electronics
Total 24 DMA channels will be initialized.
331, arch/arm/plat-s5pc1xx/s5pc1xx-cpufreq.c 1014, arch/arm/plat-s5pc1xx/s5pc1xx-cpufreq.c, Perf changed[L1]
bio: create slab <bio-0> at 0
SCSI subsystem initialized
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 5, 163840 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
LED: can set GPJ1(0) to output mode
LED: can set GPJ2(6) to output mode
S5PC1XX ADC driver, (c) 2008 Samsung Electronics
ADC platform data read
S5PC1XX ADC driver successfully probed
squashfs: version 4.0 (2009/01/31) Phillip Lougher
fuse init (API version 7.11)
msgmni has been set to 499
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
s3c_epd_init_hw() Our thread for resuming of EPD initialization : pid = 205
[EPD] EPD Initialization function completed
drivers/video/samsung/s3c_epd.c:s3c_epd_init_fbinfo:3273> finfo->fb.fix.line_length 300
drivers/video/samsung/s3c_epd.c:s3c_epd_init_fbinfo:3274> finfo->fb.var.xres=600 ,finfo->fb.var.yres=800 ,s3c_epd_fimd.bpp=4 ,finfo->fb.fix.smem_len=240000
map_video_memory(fbi=c038329c)
Window[0] - FB1: map_video_memory: clear ff000000:0003a980
FB1: map_video_memory: dma=2f980000 cpu=ff000000 size=0003a980
[EPD] epson_init thread.. wait...
fb0: s3c_epd frame buffer device
s5pc100-uart.0: s3c2410_serial0 at MMIO 0xec000000 (irq = 16) is a S3C6400/10
s5pc100-uart.1: s3c2410_serial1 at MMIO 0xec000400 (irq = 20) is a S3C6400/10
s5pc100-uart.2: s3c2410_serial2 at MMIO 0xec000800 (irq = 24) is a S3C6400/10
s5pc100-uart.3: s3c2410_serial3 at MMIO 0xec000c00 (irq = 28) is a S3C6400/10
brd: module loaded
loop: module loaded
PPP generic driver version 2.4.2
Driver 'sd' needs updating - please use bus_type methods
s3c-udc : S3C HS USB OTG Device Driver, (c) 2008-2009 Samsung Electronics
s3c-udc : version 15 March 2009 (DMA Mode) s3c_DRM proc initialised
mice: PS/2 mouse device common for all mice
input: s3c-keypad as /devices/virtual/input/input0
s3c-keypad Initialized
S3C Keypad Driver
S5PC100 Power Button init function S3C24XX RTC, (c) 2004,2006 Simtec Electronics
s3c2410-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
i2c /dev entries driver
s3c2410-i2c s3c2410-i2c.0: i2c-0: S3C I2C adapter
s3c2410-i2c s3c2410-i2c.1: i2c-1: S3C I2C adapter
Entered pmic_max8698c_probe func
[pmic]before : address[00]: 0xfe
[pmic]after: address[00]: 0x3e
[pmic]before : address[04]: 0x99
[pmic]after: address[04]: 0x89
[pmic]before : address[05]: 0x99
[pmic]after: address[05]: 0x57
[pmic]before : address[06]: 0x99
[pmic]after: address[06]: 0x59
[EPD] flash_init_2nd_half Begin
[EPD] Waiting for Operation Trigger Busy -> Completed
[EPD] Waiting for Display Frame Busy -> Completed
[EPD] flash_init_2nd_half End
[EPD] Setting Rotation Factor
[EPD] Setting Auto LUT Mode
For LUT Auto Select : EREG_UPDATE_BUF_CON==0084
[EPD] Starting to show EPD Logo
Display to EPD...... [pmic]before : address[0f]: 0x16
[pmic]after: address[0f]: 0x0c
i2c-adapter i2c-0: Client creation failed at 0xcc (1)
Resigter Control for S5PC100 /dev entries driver
S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq enabled
331, arch/arm/plat-s5pc1xx/s5pc1xx-cpufreq.c 1014, arch/arm/plat-s5pc1xx/s5pc1xx-cpufreq.c, Perf changed[L1]
cpuidle: using governor ladder
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
s3c-sdhci s3c-sdhci.0: clock source 0: hsmmc (133500000 Hz)
s3c-sdhci s3c-sdhci.0: clock source 1: hsmmc (133500000 Hz)
s3c-sdhci s3c-sdhci.0: clock source 2: mmc_bus (44500000 Hz)
mmc0: new high speed MMC card at address 0001
mmcblk0: mmc0:0001 M2G1DD 1.91 GiB mmcblk0: p1 p2 p3 p4 < p5 p6 p7 >
mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.0] using ADMA
s3c-sdhci s3c-sdhci.1: clock source 0: hsmmc (133500000 Hz)
s3c-sdhci s3c-sdhci.1: clock source 1: hsmmc (133500000 Hz)
s3c-sdhci s3c-sdhci.1: clock source 2: mmc_bus (44500000 Hz)
mmc1: new SDIO card at address 0001
mmc1: SDHCI controller on samsung-hsmmc [s3c-sdhci.1] using ADMA
s3c-sdhci s3c-sdhci.2: clock source 0: hsmmc (133500000 Hz)
s3c-sdhci s3c-sdhci.2: clock source 1: hsmmc (133500000 Hz)
s3c-sdhci s3c-sdhci.2: clock source 2: mmc_bus (44500000 Hz)
mmc2: new SD card at address aaaa
mmcblk1: mmc2:aaaa SU02G 1.84 GiB mmcblk1: p1
mmc_blk_probe:1066 ret: 0
mmc2: SDHCI controller on samsung-hsmmc [s3c-sdhci.2] using ADMA
Advanced Linux Sound Architecture Driver Version 1.0.18a.
No device for DAI WM8960 PAIFRX
No device for DAI s3c-i2s
WM8960 Audio Codec 0.2Entered wm8960_init:790
Normal mode: preallocate buffer(Playback): VA-ff03b000 PA-2FA10000 65536bytes
Normal mode: preallocate buffer(Capture): VA-ff04b000 PA-2F8A0000 65536bytes
asoc: WM8960 PAIFRX <-> s3c-i2s mapping ok
ALSA device list:
#0: smdkc100 (WM8960)
TCP cubic registered
NET: Registered protocol family 17
lib80211: common routines for IEEE802.11 drivers
VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 2
s3c2410-rtc s3c2410-rtc: setting system clock to 2077-06-11 03:35:45 UTC (3390608145)
VFS: Mounted root (squashfs filesystem) readonly on device 179:1.
Freeing init memory: 120K
eth0 (): not using net_device_ops yet
eth0: Broadcom Dongle Host Driver
Dongle Host Driver, version 4.217.34.0
rfs: module license 'Samsung, Proprietary' taints kernel.
RFS-fs error: rfs_find_last_cluster[152] fat entry(299382,0) was corrupted
highest_d_ino: 58638336
rfs_handle_crash[838]: Remounting read-only
kernel BUG at fs/rfs/super.c:847!
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = cec24000
[00000000] *pgd=2ec7a031, *pte=00000000, *ppte=00000000
Internal error: Oops: 817 [#1]
Modules linked in: rfs(P) dhd max14540
CPU: 0 Tainted: P (2.6.29.4 #1)
PC is at __bug+0x20/0x2c
LR is at release_console_sem+0x1c0/0x1fc
pc : [<c002a2d8>] lr : [<c0043914>] psr: 60000013
sp : cfb61cf8 ip : cfb61c00 fp : cfb61d04
r10: 00000042 r9 : cf44a520 r8 : 00000000
r7 : 00000040 r6 : 00000000 r5 : cfb63000 r4 : cfb63000
r3 : 00000000 r2 : 60000013 r1 : 60000093 r0 : 00000025
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 10c5387d Table: 2ec24019 DAC: 00000015
Process mount (pid: 941, stack limit = 0xcfb602e0)
Stack: (0xcfb61cf8 to 0xcfb62000)
1ce0: cfb61d20 cfb61d08 1d00: bf0340dc c002a2c4 c005b284 cfb61d28 00049176 cfb61d84 cfb61d28 bf02db3c 1d20: bf03406c bf03bff0 00049176 00000000 00000800 bf02c0ec 00000df8 00000000 1d40: cfb61dc4 00000003 00000000 000ded0a 00000028 00000000 60000013 00000000 1d60: cf1c1020 00000003 cf43cca8 cf44a520 cf44a4a0 cf1c1020 cfb61df4 cfb61d88 1d80: bf031c1c bf02d9dc 00000000 00000000 00000800 c0251b10 00000df8 00000000 1da0: cfb61df4 00000001 cf44a2d0 cfb63000 00000800 00000002 cfb61e0c 0000000b 1dc0: ffffffff ffffffff 00000020 00000000 cf1c1020 cf44a520 cfb63000 cf410a00 1de0: cf914000 00008000 cfb61e3c cfb61df8 bf0378a8 bf031a88 00000000 cf43cca8 1e00: ffffffff ffffffff ffffffff cf43cca8 cfb61e4c cfb63000 cfb63000 cfb63000 1e20: 00000003 cf410a00 cf914000 00008000 cfb61e5c cfb61e40 bf039774 bf037488 1e40: c00bd9a4 c00bd8e8 cf410a38 cf410a38 cfb61eac cfb61e60 c0099db8 bf039740 1e60: 62636d6d 70306b6c c00a0032 0000000f c00ad4a4 cf82d000 cf914000 cf888ea0 1e80: cf888ea0 cec93300 cf82d000 bf042324 00008000 cf914000 cfb61f38 00008000 1ea0: cfb61ec4 cfb61eb0 bf039588 c0099cb8 bf039734 cec93300 cfb61ef4 cfb61ec8 1ec0: c0099888 bf039570 cec93300 cfb61ed8 c00abdec 00008000 cf82d000 cf914000 1ee0: cfa0b000 bf042324 cfb61f1c cfb61ef8 c0099940 c009983c cfb61f1c 00000000 1f00: 00000000 cf82d000 00000000 cfa0b000 cfb61f6c cfb61f20 c00ae178 c009990c 1f20: cfb61f84 00000000 000e2018 cfb61f6c 00000000 cfb61f48 cf8d4b00 cf4033f0 1f40: 20000013 00000000 cfaf7000 beef7f69 00008000 c0027004 cfb60000 000e2018 1f60: cfb61fa4 cfb61f70 c00ae258 c00adb08 cf914000 000e2018 cfb61f9c cf82d000 1f80: cfa0b000 cf914000 000e2018 beef7f69 beef7f78 00000015 00000000 cfb61fa8 1fa0: c0026e80 c00ae1d8 000e2018 beef7f69 beef7f69 beef7f78 beef7f65 00008000 1fc0: 000e2018 beef7f69 beef7f78 00000015 00008000 00008000 000e2018 00000005 1fe0: beef7f65 beef76f4 00072f44 4018f344 60000010 beef7f69 06000020 0000010c Backtrace: [<c002a2b8>] (__bug+0x0/0x2c) from [<bf0340dc>] (rfs_handle_crash+0x80/0xa8 [rfs])
[<bf034060>] (rfs_handle_crash+0x4/0xa8 [rfs]) from [<bf02db3c>] (rfs_find_last_cluster+0x16c/0x2e4 [rfs])
r4:00049176
[<bf02d9d0>] (rfs_find_last_cluster+0x0/0x2e4 [rfs]) from [<bf031c1c>] (rfs_fill_inode+0x1a0/0x830 [rfs])
[<bf031a7c>] (rfs_fill_inode+0x0/0x830 [rfs]) from [<bf0378a8>] (rfs_log_init+0x42c/0x4d8 [rfs])
[<bf03747c>] (rfs_log_init+0x0/0x4d8 [rfs]) from [<bf039774>] (rfs_fill_super+0x40/0x8c [rfs])
[<bf039734>] (rfs_fill_super+0x0/0x8c [rfs]) from [<c0099db8>] (get_sb_bdev+0x10c/0x16c)
r4:cf410a38
[<c0099cac>] (get_sb_bdev+0x0/0x16c) from [<bf039588>] (rfs_get_sb+0x24/0x30 [rfs])
[<bf039564>] (rfs_get_sb+0x0/0x30 [rfs]) from [<c0099888>] (vfs_kern_mount+0x58/0xb0)
[<c0099830>] (vfs_kern_mount+0x0/0xb0) from [<c0099940>] (do_kern_mount+0x40/0xdc)
r8:bf042324 r7:cfa0b000 r6:cf914000 r5:cf82d000 r4:00008000
[<c0099900>] (do_kern_mount+0x0/0xdc) from [<c00ae178>] (do_mount+0x67c/0x6d0)
r8:cfa0b000 r7:00000000 r6:cf82d000 r5:00000000 r4:00000000
[<c00adafc>] (do_mount+0x0/0x6d0) from [<c00ae258>] (sys_mount+0x8c/0xd4)
[<c00ae1cc>] (sys_mount+0x0/0xd4) from [<c0026e80>] (ret_fast_syscall+0x0/0x2c)
r7:00000015 r6:beef7f78 r5:beef7f69 r4:000e2018
Code: e1a01000 e59f000c eb006746 e3a03000 (e5833000) ---[ end trace a42659ccd67a90bf ]---
Segmentation fault
eth0 up & down for device id
/bin/sh: can't access tty; job control turned off
# connect
dev == "/dev/fb0" connect after open
drivers/video/samsung/s3c_epd.c:s3c_epd_mmap:265> fb[0] phys-startaddr:2f980000, virt-startaddr ff000000, len:240000 drivers/video/samsung/s3c_epd.c:s3c_epd_mmap:266> startaddr from fix.smem:2f980000 : phys_to_virt:cf980000 virt_to_phys:2f980000
drivers/video/samsung/s3c_epd.c:s3c_epd_mmap:284> from the process startaddr vm_start:42627000 : virt_to_phys:a2627000
vinfo.grayscale:0 vinfo.bits_per_pixel:4 finfo.line_length:300 vinfo.xoffset:0 dw600 dh800
finfo.smem_len:240000 FBDATA [ 42627000] after mmap
1 2 FBDATA [ 42627000] after adding offset
5 startcmap.len(#ofColors)= 16 QLinuxFbScreen::connect: Invalid argument
Error reading palette from frame[s5p_serial_set_tsp_configuration] baud_rate = 19200
[s5p_serial_set_tsp_configuration] Setting FIFO Trigger(Interrupt) Level to 32[s5p_serial_set_tsp_configuration] Set Interrupt to PULSE Type
buffer, using default palette
connect returns true
QLinuxFbScreen::initDevice: Invalid argument
Error writing palette to framebuffer
Before call S5pc100MouseHandler() Could not read calibration: "/etc/pointercal" Opening tsp device...
[S5pc100MouseHandler] Opened /dev/ttySAC2
[S5pc100MouseHandler] Opened /dev/input/s5p_tspset_freezable for TSP Kernel Thread
Successfully open Touch Configuration. Setting Touch Type from it
Successfully opened tsp for touchscreen input
<1> <3> <4> Before call S5pc100KeypadHandlerS5pc100KeypadHandler() Loaded s5pc100 keypad plugin! [Handler!!] I: Bus=0019 Vendor=0001 Product=0001 Version=0001
N: Name="s3c-keypad"
P: Phys=s3c-keypad/input0
S: Sysfs=/devices/virtual/input/input0
U: Uniq=
H: Handlers=kbd event0 B: EV=100003
B: KEY=600000 0 1 dfffffff fffffffe
nReadSize== 219 [strstr() done] tmpBuf== Handlers=kbd event0 B: EV=100003
B: KEY=600000 0 1 dfffffff fffffffe
[strtok() done] tmpBuf== Handlers=kbd event0
tmpBuf== event0
[strtok() done] tmpBuf== event0 eventDrvName== /dev/input/event0 [s5pc100_keypad_hanlder] Succeeded to get event Driver Name
eventDrvName=="/dev/input/event0"
Opened /dev/input/event0 for Keypad Driver THIS DEVICE'S NEWS UPDATE TIME = QTime("07:31:04" ) [EPD] Showing Animation Logo Image is completed drivers/video/samsung/s3c_epd.c:epson_init:1448> epson_init END
|
Et voilà le log de boot en mode rescue : Citation :
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2011.05.05 17:02:42 =~=~=~=~=~=~=~=~=~=~=~=
Žà
U-Boot 1.3.4 (May 14 2010 - 18:09:39) for E6
CPU: S5PC100@666MHz
Fclk = 666MHz, Hclk = 166MHz, Pclk = 66MHz, DoutMpll = 133MHz, Serial = PCLK Board: E6 e-Diary
DRAM: 256 MB
Flash: 0 kB
SD/MMC: 1960MB
The input address don't need a virtual-to-physical translation : 27e7c008
Entering RescueMode...
Init EPD Panel.........done
In: serial
Out: serial
Err: serial
Net: No ethernet found
Hit any key to stop autoboot: 0 reading kernel.. 4004816, 8128 MMC read: dev # 0, block # 4004816, count 8128 ... 8128 blocks read: OK
completed
get_format
-------- 1 --------
## Booting kernel from Legacy Image at c0008000 ...
Image Name: Linux-2.6.29.4
Created: 2010-05-19 6:28:51 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1162620 Bytes = 1.1 MB
Load Address: 20008000
Entry Point: 20008000
Verifying Checksum ... OK
get_format
-------- 1 --------
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux.............................................................................. done, booting the kernel.
Linux version 2.6.29.4 (siwon.sung@ux-p63s) (gcc version 4.2.2) #1 Wed May 19 15:28:38 KST 2010
CPU: ARMv7 Processor [412fc081] revision 1 (ARMv7), cr=10c5387f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: SNE-60K
Ignoring unrecognised tag 0x41001099
Memory policy: ECC disabled, Data cache writeback
CPU S5PC100 (id 0x43100000)
S3C24XX Clocks, (c) 2004 Simtec Electronics
S5PC100: PLL settings, A=666000000, M=267000000, E=133000000, H=24000000
S5PC100: ARMCLK=666000000, HCLKD0=166500000, PCLKD0=83250000, HCLK=133500000, PCLK=66750000
mout_apll: source is fout_apll (1), rate is 666000000
mout_epll: source is fout_epll (1), rate is 133000000
mout_mpll: source is mpll (1), rate is 267000000
mout_hpll: source is srclk (1), rate is 24000000
mmc_bus: source is dout_mpll (1), rate is 44500000
mmc_bus: source is dout_mpll (1), rate is 44500000
mmc_bus: source is dout_mpll (1), rate is 44500000
usb-host-bus: source is dout_mpll (1), rate is 133500000
uclk1: source is dout_mpll (1), rate is 66750000
spi_epll: source is dout_mpll2 (1), rate is 66750000
spi_epll: source is dout_mpll2 (1), rate is 66750000
spi_epll: source is dout_mpll2 (1), rate is 66750000
sclk_audio0: source is mout_epll (0), rate is 133000000
sclk_audio1: source is mout_epll (0), rate is 133000000
sclk_audio2: source is mout_epll (0), rate is 133000000
i2sclkd2: source is fout_epll (0), rate is 133000000
sclk_irda: source is dout_mpll (1), rate is 133500000
sclk_pwi: source is srclk (0), rate is 0
sclk_lcd: source is dout_mpll (1), rate is 133500000
sclk_fimc: source is dout_mpll (1), rate is 133500000
sclk_fimc: source is dout_mpll (1), rate is 133500000
sclk_fimc: source is dout_mpll (1), rate is 133500000
sclk_mixer: source is clk_27m (0), rate is 27000000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
Kernel command line: root=/dev/mmcblk0p5 rootfstype=squashfs init=/linuxrc console=ttySAC0,115200 mem=256M
PID hash table entries: 1024 (order: 10, 4096 bytes)
Console: colour dummy device 80x30
console [ttySAC0] enabled
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 256MB = 256MB total
Memory: 256384KB available (2100K code, 1062K data, 96K init)
SLUB: Genslabs=12, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay loop... 665.19 BogoMIPS (lpj=1662976)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
S5PC1XX GPIO Driver Init
s5pc1xx Power Management, (c) 2008 Samsung Electronics
Created proc/sleep_wakeup/pm_mode Succssfully S5PC100: Initialising architecture
S3C PL330-DMA Controller Driver, (c) 2008-2009 Samsung Electronics
Total 24 DMA channels will be initialized.
331, arch/arm/plat-s5pc1xx/s5pc1xx-cpufreq.c 1014, arch/arm/plat-s5pc1xx/s5pc1xx-cpufreq.c, Perf changed[L1]
bio: create slab <bio-0> at 0
SCSI subsystem initialized
LED: can set GPJ1(0) to output mode
LED: can set GPJ2(6) to output mode
S5PC1XX ADC driver, (c) 2008 Samsung Electronics
ADC platform data read
S5PC1XX ADC driver successfully probed
squashfs: version 4.0 (2009/01/31) Phillip Lougher
fuse init (API version 7.11)
msgmni has been set to 501
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
s3c_epd_init_hw() Our thread for resuming of EPD initialization : pid = 157
[EPD] EPD Initialization function completed
drivers/video/samsung/s3c_epd.c:s3c_epd_init_fbinfo:3273> finfo->fb.fix.line_length 300
drivers/video/samsung/s3c_epd.c:s3c_epd_init_fbinfo:3274> finfo->fb.var.xres=600 ,finfo->fb.var.yres=800 ,s3c_epd_fimd.bpp=4 ,finfo->fb.fix.smem_len=240000
map_video_memory(fbi=c028279c)
Window[0] - FB1: map_video_memory: clear ff000000:0003a980
FB1: map_video_memory: dma=2f940000 cpu=ff000000 size=0003a980
[EPD] epson_init thread.. wait...
fb0: s3c_epd frame buffer device
s5pc100-uart.0: s3c2410_serial0 at MMIO 0xec000000 (irq = 16) is a S3C6400/10
s5pc100-uart.1: s3c2410_serial1 at MMIO 0xec000400 (irq = 20) is a S3C6400/10
s5pc100-uart.2: s3c2410_serial2 at MMIO 0xec000800 (irq = 24) is a S3C6400/10
s5pc100-uart.3: s3c2410_serial3 at MMIO 0xec000c00 (irq = 28) is a S3C6400/10
brd: module loaded
loop: module loaded
Driver 'sd' needs updating - please use bus_type methods
mice: PS/2 mouse device common for all mice
input: s3c-keypad as /devices/virtual/input/input0
s3c-keypad Initialized
S3C Keypad Driver
S5PC100 Power Button init function S3C24XX RTC, (c) 2004,2006 Simtec Electronics
s3c2410-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
i2c /dev entries driver
s3c2410-i2c s3c2410-i2c.0: i2c-0: S3C I2C adapter
s3c2410-i2c s3c2410-i2c.1: i2c-1: S3C I2C adapter
Entered pmic_max8698c_probe func
[pmic]before : address[00]: 0xfe
[pmic]after: address[00]: 0x3e
[pmic]before : address[04]: 0x99
[pmic]after: address[04]: 0x89
[pmic]before : address[05]: 0x99
[pmic]after: address[05]: 0x57
[pmic]before : address[06]: 0x99
[pmic]after: address[06]: 0x59
[pmic]before : address[0f]: 0x16
[pmic]after: address[0f]: 0x0c
i2c-adapter i2c-0: Client creation failed at 0xcc (1)
Resigter Control for S5PC100 /dev entries driver
S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq enabled
331, arch/arm/plat-s5pc1xx/s5pc1xx-cpufreq.c 1014, arch/arm/plat-s5pc1xx/s5pc1xx-cpufreq.c, Perf changed[L1]
cpuidle: using governor ladder
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
s3c-sdhci s3c-sdhci.0: clock source 0: hsmmc (133500000 Hz)
s3c-sdhci s3c-sdhci.0: clock source 1: hsmmc (133500000 Hz)
s3c-sdhci s3c-sdhci.0: clock source 2: mmc_bus (44500000 Hz)
mmc0: new high speed MMC card at address 0001
mmcblk0: mmc0:0001 M2G1DD 1.91 GiB mmcblk0: p1 p2 p3 p4 < p5 p6 p7 >
mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.0] using ADMA
s3c-sdhci s3c-sdhci.1: clock source 0: hsmmc (133500000 Hz)
s3c-sdhci s3c-sdhci.1: clock source 1: hsmmc (133500000 Hz)
s3c-sdhci s3c-sdhci.1: clock source 2: mmc_bus (44500000 Hz)
mmc1: new SDIO card at address 0001
mmc1: SDHCI controller on samsung-hsmmc [s3c-sdhci.1] using ADMA
s3c-sdhci s3c-sdhci.2: clock source 0: hsmmc (133500000 Hz)
s3c-sdhci s3c-sdhci.2: clock source 1: hsmmc (133500000 Hz)
s3c-sdhci s3c-sdhci.2: clock source 2: mmc_bus (44500000 Hz)
mmc2: new SD card at address aaaa
mmcblk1: mmc2:aaaa SU02G 1.84 GiB mmcblk1: p1
mmc_blk_probe:1066 ret: 0
mmc2: SDHCI controller on samsung-hsmmc [s3c-sdhci.2] using ADMA
VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 2
s3c2410-rtc s3c2410-rtc: setting system clock to 2077-06-11 03:37:08 UTC (3390608228)
VFS: Mounted root (squashfs filesystem) readonly on device 179:5.
Freeing init memory: 96K
[EPD] flash_init_2nd_half Begin
[EPD] Waiting for Operation Trigger Busy -> Completed
[EPD] Waiting for Display Frame Busy -> Completed
[EPD] flash_init_2nd_half End
[EPD] Setting Rotation Factor
[EPD] Setting Auto LUT Mode
For LUT Auto Select : EREG_UPDATE_BUF_CON==0084
[EPD] Starting to show EPD Logo
Display to EPD...... rfs: module license 'Samsung, Proprietary' taints kernel.
RFS-fs error: rfs_find_last_cluster[159] fat entry(299382,0) was corrupted
rfs_handle_crash[830]: Remounting read-only
kernel BUG at fs/rfs/super.c:839!
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = cfa84000
[00000000] *pgd=2fa8e031, *pte=00000000, *ppte=00000000
Internal error: Oops: 817 [#1]
Modules linked in: rfs(P)
CPU: 0 Tainted: P (2.6.29.4 #1)
PC is at __bug+0x20/0x2c
LR is at release_console_sem+0x1c0/0x1fc
pc : [<c00242d8>] lr : [<c003d818>] psr: 60000013
sp : cfa8dd10 ip : cfa8dc18 fp : cfa8dd1c
r10: 00000042 r9 : cf43e500 r8 : 00000000
r7 : 00000040 r6 : 00000000 r5 : cf83f800 r4 : cf83f800
r3 : 00000000 r2 : 60000013 r1 : 60000093 r0 : 00000025
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 10c5387d Table: 2fa84019 DAC: 00000015
Process mount (pid: 858, stack limit = 0xcfa8c2e0)
Stack: (0xcfa8dd10 to 0xcfa8e000)
dd00: cfa8dd38 cfa8dd20 bf007540 c00242c4 dd20: c0055180 cfa8dd40 00049176 cfa8dd9c cfa8dd40 bf001a18 bf0074e0 bf00edf4 dd40: 00049176 00000000 00000000 000000d0 00000008 00000008 cfa8ddc4 00000003 dd60: 00000000 000ded0a cf83f800 00000000 00000002 00000000 00000001 cf43e500 dd80: cf83f800 00000002 cf43e480 c064e020 cfa8ddf4 cfa8dda0 bf005544 bf0018b8 dda0: 00000000 00000000 bf003300 c00b42d0 cf43e2c0 cf83f800 cfa8de0c 0000000b ddc0: ffffffff ffffffff 00000020 00000000 c064e020 cf43e500 cf83f800 cf410a00 dde0: cf9ba000 00008000 cfa8de3c cfa8ddf8 bf00ac10 bf005488 00000000 dead4ead de00: ffffffff ffffffff ffffffff cf4314c8 cfa8de4c cf83f800 cf83f800 cf83f800 de20: 00000003 cf410a00 cf9ba000 00008000 cfa8de5c cfa8de40 bf00ca58 bf00a820 de40: c00b78a0 c00b77e4 cf410a38 cf83f800 cfa8deac cfa8de60 c0093cb4 bf00ca24 de60: 62636d6d 70306b6c c00a0032 0000000f c00a73a0 cf86b000 cf9ba000 cf9de630 de80: cf9de630 cfa0f380 cf86b000 bf014694 00008000 cf9ba000 cfa8df38 00008000 dea0: cfa8dec4 cfa8deb0 bf00c880 c0093bb4 bf00ca18 cfa0f380 cfa8def4 cfa8dec8 dec0: c0093784 bf00c868 cfa0f380 cfa8ded8 c00a5ce8 00008000 cf86b000 cf9ba000 dee0: cfa0e000 bf014694 cfa8df1c cfa8def8 c009383c c0093738 cfa8df1c 00000000 df00: 00000000 cf86b000 00000000 cfa0e000 cfa8df6c cfa8df20 c00a8074 c0093808 df20: cfa8df84 00000000 000e2018 cfa8df6c 00000000 cfa8df48 cf8d3280 cf4046c0 df40: 20000013 00000000 cfa74000 becabf69 00008000 c0021004 cfa8c000 000e2018 df60: cfa8dfa4 cfa8df70 c00a8154 c00a7a04 cf9ba000 000e2018 cfa8df9c cf86b000 df80: cfa0e000 cf9ba000 000e2018 becabf69 becabf78 00000015 00000000 cfa8dfa8 dfa0: c0020e80 c00a80d4 000e2018 becabf69 becabf69 becabf78 becabf65 00008000 dfc0: 000e2018 becabf69 becabf78 00000015 00008000 00008000 000e2018 00000005 dfe0: becabf65 becab6f4 00072f44 4018f344 60000010 becabf69 0000691c 0002121c Backtrace: [<c00242b8>] (__bug+0x0/0x2c) from [<bf007540>] (rfs_handle_crash+0x70/0x94 [rfs])
[<bf0074d4>] (rfs_handle_crash+0x4/0x94 [rfs]) from [<bf001a18>] (rfs_find_last_cluster+0x16c/0x2e4 [rfs])
r4:00049176
[<bf0018ac>] (rfs_find_last_cluster+0x0/0x2e4 [rfs]) from [<bf005544>] (rfs_fill_inode+0xc8/0x6ec [rfs])
[<bf00547c>] (rfs_fill_inode+0x0/0x6ec [rfs]) from [<bf00ac10>] (rfs_log_init+0x3fc/0x4a8 [rfs])
[<bf00a814>] (rfs_log_init+0x0/0x4a8 [rfs]) from [<bf00ca58>] (rfs_fill_super+0x40/0xa8 [rfs])
[<bf00ca18>] (rfs_fill_super+0x0/0xa8 [rfs]) from [<c0093cb4>] (get_sb_bdev+0x10c/0x16c)
r5:cf83f800 r4:cf410a38
[<c0093ba8>] (get_sb_bdev+0x0/0x16c) from [<bf00c880>] (rfs_get_sb+0x24/0x30 [rfs])
[<bf00c85c>] (rfs_get_sb+0x0/0x30 [rfs]) from [<c0093784>] (vfs_kern_mount+0x58/0xb0)
[<c009372c>] (vfs_kern_mount+0x0/0xb0) from [<c009383c>] (do_kern_mount+0x40/0xdc)
r8:bf014694 r7:cfa0e000 r6:cf9ba000 r5:cf86b000 r4:00008000
[<c00937fc>] (do_kern_mount+0x0/0xdc) from [<c00a8074>] (do_mount+0x67c/0x6d0)
r8:cfa0e000 r7:00000000 r6:cf86b000 r5:00000000 r4:00000000
[<c00a79f8>] (do_mount+0x0/0x6d0) from [<c00a8154>] (sys_mount+0x8c/0xd4)
[<c00a80c8>] (sys_mount+0x0/0xd4) from [<c0020e80>] (ret_fast_syscall+0x0/0x2c)
r7:00000015 r6:becabf78 r5:becabf69 r4:000e2018
Code: e1a01000 e59f000c eb006707 e3a03000 (e5833000) ---[ end trace 76e35c0b8ee1f8c3 ]---
Segmentation fault
updating E60K.bin in /mnt/sd....
enter autoupdate 2
The framebuffer device was opened successfully.
source Dir : /mnt/sd/Firmware_Update/E60K.bin
current package is E60K.bin
version 1002.0
kernel file size : 1692808 system file size: 45371392 [EPD] Showing Animation Logo Image is completed drivers/video/samsung/s3c_epd.c:epson_init:1448> epson_init END
drivers/video/samsung/s3c_epd.c:pm_from_standby:555> new_epd_state is RUN
device=/dev/mmcblk0p6 filename=/mnt/sd/Firmware_Update/E60K.bin 32::1692808
copying
10%
20%
30%
40%
50%
60%
70%
80%
90%
100%
syncing
device=/dev/mmcblk0p1 filename=/mnt/sd/Firmware_Update/E60K.bin 1692840::45371392
copying
10%
20%
30%
40%
50%
60%
70%
80%
90%
100%
syncing
|
---------------
Quand un Linuxien me répond, je ne comprends plus ma question !!!
|