raptor68 Pouet ! Transactions (9) | Bonjour à tous, j'ai un lot d'item potentiellement utile mais dans une état relativement moyen, vous avez une idée de si ça pourrait intéresser quelqu'un ici?
Carte controlleur SAS LSI MegaRAID 9341-4i (totalement fonctionnelle, passé en firmware IT 9300-4i P16b pour la compatibilité ZFS mais verrou du connecteur SFF-8643 cassé, donc la rétention du cable est moins bonne, fournie avec équerre full et low profile)
https://docs.broadcom.com/doc/12351983
Expander SAS Adaptec 82885T 12Gbps 36 ports (28 interne 8 externe) avec alimentation possible via port pcie ou prise molex pour usage DAS (fournie avec équerre full et low profile)
https://storage.microsemi.com/en-us [...] ec-82885t/
4x HGST HUS724030ALS640 (3To 7200RPM 64Mo SAS-2, 6 en réalité mais 2 d'entre eux ont du "Elements in grown defect list" dans leur table SMART, donc donné avec le reste au cas où car SMART OK, mais non compté dans le prix global)
https://documents.westerndigital.co [...] 7k4000.pdf
4 Cables SFF-8643:
- 1x 8643 vers 8643 (pour l'expander) (acheté neuf il y'a moins de 3 mois)
- 1x 8643 vers sata x4 (fourni avec la carte controlleur à l'achat sur ebay)
- 1x 8643 vers SAS avec alimentation SATA (acheté neuf il y'a moins de 3 mois)
- 1x 8643 vers SAS avec alimentation Molex (acheté neuf il y'a moins de 3 mois)
Le cout global de l'ensemble était à plus de 250€ d'occasion, mais comme j'ai abimé le verrou du connecteur de l'HBA, et que les disques sont vieux, je n'en demanderai que 125 pour l'ensemble (tout acheté il y'a moins de 3 mois)
Accepte également échanges contre films, séries et JV physiques (PC, 3DS et Switch uniquement) ou composants selon offre
Rapports SMART des disques OK:
Spoiler :
smartctl 7.2 2020-12-30 r5155 [x86_64-linux-6.2.16-11-bpo11-pve] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Vendor: HGST
Product: HUS724030ALS640
Revision: A1C4
Compliance: SPC-4
User Capacity: 3 000 592 982 016 bytes [3,00 TB]
Logical block size: 512 bytes
LU is resource provisioned, LBPRZ=0
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Logical Unit id: 0x5000cca0278ef8e8
Serial number: P8JJMJ5W
Device type: disk
Transport protocol: SAS (SPL-3)
Local Time is: Sun Dec 10 12:47:52 2023 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
Temperature Warning: Enabled
Read Cache is: Enabled
Writeback Cache is: Disabled
=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK
Current Drive Temperature: 31 C
Drive Trip Temperature: 85 C
Manufactured in week 47 of year 2013
Specified cycle count over device lifetime: 50000
Accumulated start-stop cycles: 16
Specified load-unload count over device lifetime: 600000
Accumulated load-unload cycles: 2188
Elements in grown defect list: 0
Vendor (Seagate Cache) information
Blocks sent to initiator = 1866667260903424
Error counter log:
Errors Corrected by Total Correction Gigabytes Total
ECC rereads/ errors algorithm processed uncorrected
fast | delayed rewrites corrected invocations [10^9 bytes] errors
read: 2130074 73 0 2130147 47954291 468996,836 0
write: 0 2 0 2 353975 46954,320 0
verify: 0 0 0 0 50344 0,000 0
Non-medium error count: 0
SMART Self-test log
Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ]
Description number (hours)
# 1 Background long Self test in progress ... 7 NOW - [- - -]
# 2 Background short Completed - 53047 - [- - -]
Long (extended) Self-test duration: 29637 seconds [493,9 minutes]
Background scan results log
Status: waiting until BMS interval timer expires
Accumulated power on time, hours:minutes 53096:02 [3185762 minutes]
Number of background scans performed: 257, scan progress: 0,00%
Number of background medium scans performed: 257
Protocol Specific port log page for SAS SSP
relative target port id = 1
generation code = 2
number of phys = 1
phy identifier = 0
attached device type: SAS or SATA device
attached reason: power on
reason: unknown
negotiated logical link rate: phy enabled; 6 Gbps
attached initiator port: ssp=1 stp=1 smp=1
attached target port: ssp=0 stp=0 smp=0
SAS address = 0x5000cca0278ef8e9
attached SAS address = 0x500605b0073ef440
attached phy identifier = 0
Invalid DWORD count = 5
Running disparity error count = 5
Loss of DWORD synchronization = 3
Phy reset problem = 0
Phy event descriptors:
Invalid word count: 5
Running disparity error count: 5
Loss of dword synchronization count: 3
Phy reset problem count: 0
relative target port id = 2
generation code = 2
number of phys = 1
phy identifier = 1
attached device type: no device attached
attached reason: unknown
reason: power on
negotiated logical link rate: phy enabled; unknown
attached initiator port: ssp=0 stp=0 smp=0
attached target port: ssp=0 stp=0 smp=0
SAS address = 0x5000cca0278ef8ea
attached SAS address = 0x0
attached phy identifier = 0
Invalid DWORD count = 0
Running disparity error count = 0
Loss of DWORD synchronization = 0
Phy reset problem = 0
Phy event descriptors:
Invalid word count: 0
Running disparity error count: 0
Loss of dword synchronization count: 0
Phy reset problem count: 0 |
Spoiler :
smartctl 7.2 2020-12-30 r5155 [x86_64-linux-6.2.16-11-bpo11-pve] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Vendor: HGST
Product: HUS724030ALS640
Revision: A1C4
Compliance: SPC-4
User Capacity: 3 000 592 982 016 bytes [3,00 TB]
Logical block size: 512 bytes
LU is resource provisioned, LBPRZ=0
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Logical Unit id: 0x5000cca0279290e0
Serial number: P8JLLTGW
Device type: disk
Transport protocol: SAS (SPL-3)
Local Time is: Fri Dec 8 05:28:58 2023 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
Temperature Warning: Enabled
Read Cache is: Enabled
Writeback Cache is: Disabled
=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK
Current Drive Temperature: 39 C
Drive Trip Temperature: 85 C
Manufactured in week 47 of year 2013
Specified cycle count over device lifetime: 50000
Accumulated start-stop cycles: 98
Specified load-unload count over device lifetime: 600000
Accumulated load-unload cycles: 2153
Elements in grown defect list: 0
Vendor (Seagate Cache) information
Blocks sent to initiator = 14729826212511744
Error counter log:
Errors Corrected by Total Correction Gigabytes Total
ECC rereads/ errors algorithm processed uncorrected
fast | delayed rewrites corrected invocations [10^9 bytes] errors
read: 7874173 317 0 7874490 18994170 448933,745 0
write: 0 0 0 0 328248 115730,955 0
verify: 0 0 0 0 75237 0,000 0
Non-medium error count: 0
SMART Self-test log
Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ]
Description number (hours)
# 1 Background long Completed - 51280 - [- - -]
# 2 Background short Completed - 51272 - [- - -]
Long (extended) Self-test duration: 29637 seconds [493,9 minutes]
Background scan results log
Status: scan is active
Accumulated power on time, hours:minutes 52933:38 [3176018 minutes]
Number of background scans performed: 167, scan progress: 100,00%
Number of background medium scans performed: 167
Protocol Specific port log page for SAS SSP
relative target port id = 1
generation code = 2
number of phys = 1
phy identifier = 0
attached device type: SAS or SATA device
attached reason: unknown
reason: unknown
negotiated logical link rate: phy enabled; 6 Gbps
attached initiator port: ssp=1 stp=1 smp=1
attached target port: ssp=0 stp=0 smp=0
SAS address = 0x5000cca0279290e1
attached SAS address = 0x500605b0073ef443
attached phy identifier = 3
Invalid DWORD count = 3
Running disparity error count = 3
Loss of DWORD synchronization = 3
Phy reset problem = 0
Phy event descriptors:
Invalid word count: 3
Running disparity error count: 3
Loss of dword synchronization count: 3
Phy reset problem count: 0
relative target port id = 2
generation code = 2
number of phys = 1
phy identifier = 1
attached device type: no device attached
attached reason: unknown
reason: power on
negotiated logical link rate: phy enabled; unknown
attached initiator port: ssp=0 stp=0 smp=0
attached target port: ssp=0 stp=0 smp=0
SAS address = 0x5000cca0279290e2
attached SAS address = 0x0
attached phy identifier = 0
Invalid DWORD count = 0
Running disparity error count = 0
Loss of DWORD synchronization = 0
Phy reset problem = 0
Phy event descriptors:
Invalid word count: 0
Running disparity error count: 0
Loss of dword synchronization count: 0
Phy reset problem count: 0 |
Spoiler :
smartctl 7.2 2020-12-30 r5155 [x86_64-linux-6.2.16-11-bpo11-pve] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Vendor: HGST
Product: HUS724030ALS640
Revision: A1C4
Compliance: SPC-4
User Capacity: 3 000 592 982 016 bytes [3,00 TB]
Logical block size: 512 bytes
LU is resource provisioned, LBPRZ=0
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Logical Unit id: 0x5000cca0275d8570
Serial number: P8HNEEHW
Device type: disk
Transport protocol: SAS (SPL-3)
Local Time is: Fri Dec 8 05:28:54 2023 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
Temperature Warning: Enabled
Read Cache is: Enabled
Writeback Cache is: Disabled
=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK
Current Drive Temperature: 37 C
Drive Trip Temperature: 85 C
Manufactured in week 39 of year 2013
Specified cycle count over device lifetime: 50000
Accumulated start-stop cycles: 81
Specified load-unload count over device lifetime: 600000
Accumulated load-unload cycles: 2135
Elements in grown defect list: 0
Vendor (Seagate Cache) information
Blocks sent to initiator = 14274928022913024
Error counter log:
Errors Corrected by Total Correction Gigabytes Total
ECC rereads/ errors algorithm processed uncorrected
fast | delayed rewrites corrected invocations [10^9 bytes] errors
read: 2325586 3 0 2325589 18558750 453235,859 0
write: 0 8 0 8 288722 113308,215 0
verify: 0 0 0 0 13450 0,000 0
Non-medium error count: 0
SMART Self-test log
Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ]
Description number (hours)
# 1 Background long Completed - 51256 - [- - -]
# 2 Background short Completed - 51248 - [- - -]
Long (extended) Self-test duration: 29637 seconds [493,9 minutes]
Background scan results log
Status: scan is active
Accumulated power on time, hours:minutes 52910:45 [3174645 minutes]
Number of background scans performed: 163, scan progress: 100,00%
Number of background medium scans performed: 163
Protocol Specific port log page for SAS SSP
relative target port id = 1
generation code = 2
number of phys = 1
phy identifier = 0
attached device type: SAS or SATA device
attached reason: unknown
reason: unknown
negotiated logical link rate: phy enabled; 6 Gbps
attached initiator port: ssp=1 stp=1 smp=1
attached target port: ssp=0 stp=0 smp=0
SAS address = 0x5000cca0275d8571
attached SAS address = 0x500605b0073ef442
attached phy identifier = 2
Invalid DWORD count = 4
Running disparity error count = 4
Loss of DWORD synchronization = 3
Phy reset problem = 0
Phy event descriptors:
Invalid word count: 4
Running disparity error count: 4
Loss of dword synchronization count: 3
Phy reset problem count: 0
relative target port id = 2
generation code = 2
number of phys = 1
phy identifier = 1
attached device type: no device attached
attached reason: unknown
reason: power on
negotiated logical link rate: phy enabled; unknown
attached initiator port: ssp=0 stp=0 smp=0
attached target port: ssp=0 stp=0 smp=0
SAS address = 0x5000cca0275d8572
attached SAS address = 0x0
attached phy identifier = 0
Invalid DWORD count = 0
Running disparity error count = 0
Loss of DWORD synchronization = 0
Phy reset problem = 0
Phy event descriptors:
Invalid word count: 0
Running disparity error count: 0
Loss of dword synchronization count: 0
Phy reset problem count: 0 |
Spoiler :
smartctl 7.2 2020-12-30 r5155 [x86_64-linux-6.2.16-11-bpo11-pve] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Vendor: HGST
Product: HUS724030ALS640
Revision: A1C4
Compliance: SPC-4
User Capacity: 3 000 592 982 016 bytes [3,00 TB]
Logical block size: 512 bytes
LU is resource provisioned, LBPRZ=0
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Logical Unit id: 0x5000cca02795f30c
Serial number: P8JNGGPW
Device type: disk
Transport protocol: SAS (SPL-3)
Local Time is: Fri Dec 8 05:28:49 2023 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
Temperature Warning: Enabled
Read Cache is: Enabled
Writeback Cache is: Disabled
=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK
Current Drive Temperature: 38 C
Drive Trip Temperature: 85 C
Manufactured in week 48 of year 2013
Specified cycle count over device lifetime: 50000
Accumulated start-stop cycles: 155
Specified load-unload count over device lifetime: 600000
Accumulated load-unload cycles: 2203
Elements in grown defect list: 0
Vendor (Seagate Cache) information
Blocks sent to initiator = 14702105151406080
Error counter log:
Errors Corrected by Total Correction Gigabytes Total
ECC rereads/ errors algorithm processed uncorrected
fast | delayed rewrites corrected invocations [10^9 bytes] errors
read: 4194314 0 0 4194314 18597471 462510,355 0
write: 0 0 0 0 334645 117840,598 0
verify: 0 0 0 0 3435 0,000 0
Non-medium error count: 0
SMART Self-test log
Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ]
Description number (hours)
# 1 Background long Completed - 51033 - [- - -]
# 2 Background short Completed - 51026 - [- - -]
Long (extended) Self-test duration: 29637 seconds [493,9 minutes]
Background scan results log
Status: scan is active
Accumulated power on time, hours:minutes 52687:36 [3161256 minutes]
Number of background scans performed: 147, scan progress: 100,00%
Number of background medium scans performed: 147
Protocol Specific port log page for SAS SSP
relative target port id = 1
generation code = 2
number of phys = 1
phy identifier = 0
attached device type: SAS or SATA device
attached reason: unknown
reason: unknown
negotiated logical link rate: phy enabled; 6 Gbps
attached initiator port: ssp=1 stp=1 smp=1
attached target port: ssp=0 stp=0 smp=0
SAS address = 0x5000cca02795f30d
attached SAS address = 0x500605b0073ef441
attached phy identifier = 1
Invalid DWORD count = 2
Running disparity error count = 2
Loss of DWORD synchronization = 3
Phy reset problem = 0
Phy event descriptors:
Invalid word count: 2
Running disparity error count: 2
Loss of dword synchronization count: 3
Phy reset problem count: 0
relative target port id = 2
generation code = 2
number of phys = 1
phy identifier = 1
attached device type: no device attached
attached reason: unknown
reason: power on
negotiated logical link rate: phy enabled; unknown
attached initiator port: ssp=0 stp=0 smp=0
attached target port: ssp=0 stp=0 smp=0
SAS address = 0x5000cca02795f30e
attached SAS address = 0x0
attached phy identifier = 0
Invalid DWORD count = 0
Running disparity error count = 0
Loss of DWORD synchronization = 0
Phy reset problem = 0
Phy event descriptors:
Invalid word count: 0
Running disparity error count: 0
Loss of dword synchronization count: 0
Phy reset problem count: 0 |
Rapports SMART des autres:
Spoiler :
smartctl 7.2 2020-12-30 r5155 [x86_64-linux-6.2.16-11-bpo11-pve] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Vendor: HGST
Product: HUS724030ALS640
Revision: A1C4
Compliance: SPC-4
User Capacity: 3 000 592 982 016 bytes [3,00 TB]
Logical block size: 512 bytes
LU is resource provisioned, LBPRZ=0
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Logical Unit id: 0x5000cca02795c1b0
Serial number: P8JNB5TW
Device type: disk
Transport protocol: SAS (SPL-3)
Local Time is: Fri Dec 8 05:28:43 2023 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
Temperature Warning: Enabled
Read Cache is: Enabled
Writeback Cache is: Disabled
=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK
Current Drive Temperature: 36 C
Drive Trip Temperature: 85 C
Manufactured in week 51 of year 2013
Specified cycle count over device lifetime: 50000
Accumulated start-stop cycles: 1128
Specified load-unload count over device lifetime: 600000
Accumulated load-unload cycles: 3174
Elements in grown defect list: 1
Vendor (Seagate Cache) information
Blocks sent to initiator = 14194202569080832
Error counter log:
Errors Corrected by Total Correction Gigabytes Total
ECC rereads/ errors algorithm processed uncorrected
fast | delayed rewrites corrected invocations [10^9 bytes] errors
read: 1758700 33 0 1758733 18832396 457727,282 0
write: 0 0 0 0 421099 111594,267 0
verify: 0 0 0 0 6567 0,000 0
Non-medium error count: 0
SMART Self-test log
Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ]
Description number (hours)
# 1 Background long Completed - 50961 - [- - -]
# 2 Background short Completed - 50953 - [- - -]
Long (extended) Self-test duration: 29637 seconds [493,9 minutes]
Background scan results log
Status: scan is active
Accumulated power on time, hours:minutes 52581:27 [3154887 minutes]
Number of background scans performed: 150, scan progress: 100,00%
Number of background medium scans performed: 150
Protocol Specific port log page for SAS SSP
relative target port id = 1
generation code = 1
number of phys = 1
phy identifier = 0
attached device type: SAS or SATA device
attached reason: power on
reason: unknown
negotiated logical link rate: phy enabled; 6 Gbps
attached initiator port: ssp=1 stp=1 smp=1
attached target port: ssp=0 stp=0 smp=0
SAS address = 0x5000cca02795c1b1
attached SAS address = 0x500605b0073ef440
attached phy identifier = 0
Invalid DWORD count = 0
Running disparity error count = 0
Loss of DWORD synchronization = 1
Phy reset problem = 0
Phy event descriptors:
Invalid word count: 0
Running disparity error count: 0
Loss of dword synchronization count: 1
Phy reset problem count: 0
relative target port id = 2
generation code = 1
number of phys = 1
phy identifier = 1
attached device type: no device attached
attached reason: unknown
reason: power on
negotiated logical link rate: phy enabled; unknown
attached initiator port: ssp=0 stp=0 smp=0
attached target port: ssp=0 stp=0 smp=0
SAS address = 0x5000cca02795c1b2
attached SAS address = 0x0
attached phy identifier = 0
Invalid DWORD count = 0
Running disparity error count = 0
Loss of DWORD synchronization = 0
Phy reset problem = 0
Phy event descriptors:
Invalid word count: 0
Running disparity error count: 0
Loss of dword synchronization count: 0
Phy reset problem count: 0 |
Spoiler :
smartctl 7.2 2020-12-30 r5155 [x86_64-linux-6.2.16-11-bpo11-pve] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Vendor: HGST
Product: HUS724030ALS640
Revision: A124
Compliance: SPC-4
User Capacity: 3 000 592 982 016 bytes [3,00 TB]
Logical block size: 512 bytes
LU is resource provisioned, LBPRZ=0
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Logical Unit id: 0x5000cca0585cc940
Serial number: P9HN0WZW
Device type: disk
Transport protocol: SAS (SPL-3)
Local Time is: Sat Dec 9 19:11:03 2023 CET
SMART support is: Available - device has SMART capability.
SMART support is: Disabled
Temperature Warning: Disabled or Not Supported
Read Cache is: Enabled
Writeback Cache is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK
Current Drive Temperature: 35 C
Drive Trip Temperature: 85 C
Manufactured in week 08 of year 2015
Specified cycle count over device lifetime: 50000
Accumulated start-stop cycles: 127
Specified load-unload count over device lifetime: 600000
Accumulated load-unload cycles: 224
Elements in grown defect list: 15
Vendor (Seagate Cache) information
Blocks sent to initiator = 1455322203947008
Error counter log:
Errors Corrected by Total Correction Gigabytes Total
ECC rereads/ errors algorithm processed uncorrected
fast | delayed rewrites corrected invocations [10^9 bytes] errors
read: 55148716 804 0 55149520 141334 11607,116 0
write: 0 0 0 0 7913 14523,025 0
verify: 0 0 0 0 1292113 0,000 0
Non-medium error count: 1
SMART Self-test log
Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ]
Description number (hours)
# 1 Background long Completed - 25752 - [- - -]
# 2 Background short Completed - 25743 - [- - -]
# 3 Background long Completed - 24701 - [- - -]
# 4 Background short Completed - 24694 - [- - -]
Long (extended) Self-test duration: 29637 seconds [493,9 minutes]
Background scan results log
Status: scan is active
Accumulated power on time, hours:minutes 25806:26 [1548386 minutes]
Number of background scans performed: 166, scan progress: 3,88%
Number of background medium scans performed: 166
Protocol Specific port log page for SAS SSP
relative target port id = 1
generation code = 4
number of phys = 1
phy identifier = 0
attached device type: SAS or SATA device
attached reason: unknown
reason: unknown
negotiated logical link rate: phy enabled; 6 Gbps
attached initiator port: ssp=1 stp=1 smp=1
attached target port: ssp=0 stp=0 smp=0
SAS address = 0x5000cca0585cc941
attached SAS address = 0x500605b0073ef442
attached phy identifier = 2
Invalid DWORD count = 10
Running disparity error count = 10
Loss of DWORD synchronization = 7
Phy reset problem = 0
Phy event descriptors:
Invalid word count: 10
Running disparity error count: 10
Loss of dword synchronization count: 7
Phy reset problem count: 0
relative target port id = 2
generation code = 4
number of phys = 1
phy identifier = 1
attached device type: no device attached
attached reason: unknown
reason: power on
negotiated logical link rate: phy enabled; unknown
attached initiator port: ssp=0 stp=0 smp=0
attached target port: ssp=0 stp=0 smp=0
SAS address = 0x5000cca0585cc942
attached SAS address = 0x0
attached phy identifier = 0
Invalid DWORD count = 0
Running disparity error count = 0
Loss of DWORD synchronization = 0
Phy reset problem = 0
Phy event descriptors:
Invalid word count: 0
Running disparity error count: 0
Loss of dword synchronization count: 0
Phy reset problem count: 0 |
Merci par avance Message édité par raptor68 le 10-12-2023 à 14:01:36
|