lol, 
Bon,sa ne marche toujours pas, sa bloque à se niveau
Bienvenue avec minicom 2.1
OPTIONS: History Buffer, F-key Macros, Search History Buffer, I18n
Compil0 le Mar 29 2005, 09:39:09.
Tapez CTRL-A Z pour voir l'aide concernant les touches sp0ciales
DIMM 0, none found
DIMM 1, RxCxB, Size/Index = DxAx4, 1x256MB/8, OK
DIMM 2, none found
DIMM 3, none found
L2 Cache: 256K, 8-way
Sun Cobalt - Smaller, Bluer, Better
Firmware version 2.9.36
Current date: Mar 28 13:30:21 UTC 1976
ROM build info: Tue May 28 12:34:03 PDT 2002 sun.cobalt.com
System serial number: Uninitialized
System type: 5000 series system, Version 2 board
Silicon serial number: 5332343930323133
Monitor: 153776 bytes
Memory: 256 MB
Initializing Local APIC ID 0 at 0xfee00000 (Virtual Wire mode)
SMP: relocate AP boot code from 0x01617200 to 0x0000a000 [size=65]
SMP: attempting to start CPU 3
Sending Start-Up IPI (Edge/Assert) to APIC 3 [vector 0x0a]
Sending Start-Up IPI (Edge/Assert) to APIC 3 [vector 0x0a]
Sending Start-Up IPI (Edge/Assert) to APIC 3 [vector 0x0a]
SMP: CPU 3 not found!
CPU: 1 processor(s) detected
CPU 0: GenuineIntel 997MHz (7.5 x 133MHz host bus) [BSP]
Initializing flash: done
Flash Bank 0: AMD AM29F016B 2048KB (01:ad)
Flash Bank 1: not installed.
Mounting ROM fs: done
Initializing PCI: PIRQ: Relocate table to 0xf8000 (96 bytes, 4 entries, checksu) OSB4 I/O port: 00:78 I/O base 0xfcfc [size=4]
OSB4 I/O port: 00:78 I/O base 0xfcf8 [size=4]
OSB4 I/O port: 00:78 I/O base 0xfcf4 [size=4]
OSB4 I/O port: 00:78 I/O base 0xfce8 [size=8]
OSB4 I/O port: 00:78 I/O base 0xfce0 [size=8]
done
Host Bus: 0 (device 00:00) [33MHz]
Device: 00:00 1166:0009 ServerWorks CNB30LE Host Bridge
Device: 00:01 1166:0009 ServerWorks CNB30LE Host Bridge
Device: 0f:00 1166:0201 ServerWorks CSB5 South Bridge (IRQ 10)
Device: 0f:01 1166:0212 ServerWorks CSB5 IDE Controller
Device: 0f:02 1166:0220 ServerWorks OpenHCI USB Controller (IRQ 9)
Device: 0f:03 1166:0230 ServerWorks CSB5 PCI-LPC Bridge
Host Bus: 1 (device 00:01) [33MHz]
Device: 06:00 100b:0020 National DP83815 MacPhyter Ethernet (IRQ 5)
Device: 07:00 100b:0020 National DP83815 MacPhyter Ethernet (IRQ 7)
MPTABLE: Bus #0 is PCI
MPTABLE: Bus #1 is PCI
MPTABLE: Bus #2 is ISA
MPTABLE: I/O Interrupt Entries
MPTABLE: TYPE POLARITY TRIGGER BUS IRQ APIC INT
MPTABLE: -------------------------------------------------------
MPTABLE: INT active-lo level PCI0 15:A 4 9
MPTABLE: INT active-lo level PCI1 6:A 5 0
MPTABLE: INT active-lo level PCI1 7:A 5 1
MPTABLE: EXT active-hi edge ISA 0 4 0
MPTABLE: INT active-hi edge ISA 0 4 0
MPTABLE: INT active-hi edge ISA 1 4 1
MPTABLE: INT active-hi edge ISA 3 4 3
MPTABLE: INT active-hi edge ISA 4 4 4
MPTABLE: INT active-hi edge ISA 8 4 8
MPTABLE: INT active-lo level ISA 10 4 10
MPTABLE: INT active-hi level ISA 14 4 14
MPTABLE: INT active-hi level ISA 15 4 15
MPTABLE: Local Interrupt Entries
MPTABLE: TYPE POLARITY TRIGGER BUS IRQ APIC INT
MPTABLE: -------------------------------------------------------
MPTABLE: EXT active-hi edge ISA 0 255 0
MPTABLE: NMI active-hi edge PCI0 0:A 255 1
SMP: floating table base 0x000f8200 (16 bytes, checksum ff)
SMP: config mptable base 0x000f8210 (216 bytes, checksum fb)
SMP: extended entry base 0x000f82e8 (144 bytes, checksum f3)
Initializing ethernet: 2 controller(s) found
National Semiconductor DP83815 Found at port 0xfe00, MAC: 00:10:e0:06:11:3e
National Semiconductor DP83815 Found at port 0xfd00, MAC: 00:10:e0:06:13:55
Initializing IDE: found ServerWorks CSB5 at 00:79
spinning up second channel: done
scanning ide0: master
scanning ide1:
IDE: stabilizing spinup: 100%
Checking Memory: done
Press spacebar to enter ROM mode
Cobalt:Main Menu> lowlevel
Cobalt:Lowlevel Hardware Menu> cmos
Cobalt:CMOS Menu> btoip 192 168 0 1
Cobalt:CMOS Menu> main
Cobalt:Main Menu> bfn
First stage kernel (Linux): Decompressing - done
command line: 'console=ttyS0,115200 debug ip=on root=/dev/nfs nfsroot=192.168.0'booting kernel...
Linux version 2.4.16C13_ROM (root@sun.cobalt.com) (gcc version egcs-2.91.66 1992BIOS-provided physical RAM map:
BIOS-e801: 0000000000000000 - 000000000009f000 (usable)
BIOS-e801: 0000000000100000 - 0000000010000000 (usable)
On node 0 totalpages: 65536
zone(0): 4096 pages.
zone(1): 61440 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0,115200 debug ip=on root=/dev/nfs nfsroot=192
Initializing CPU#0
Detected 997.194 MHz processor.
Calibrating delay loop... 1985.74 BogoMIPS
Memory: 255564k/262144k available (1487k kernel code, 6192k reserved, 258k data)Dentry-cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
CPU: Before vendor init, caps: 0387fbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After vendor init, caps: 0387fbff 00000000 00000000 00000000
CPU serial number disabled.
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
CPU: Intel Pentium III (Coppermine) stepping 0a
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Discovered primary peer bus 01 [IRQ]
PCI: Using IRQ router ServerWorks [1166/0201] at 00:0f.0
PCI: Found IRQ 9 for device 00:0f.3
PCI: Sharing IRQ 9 with 00:0f.2
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Diskquotas version dquot_6.4.0 initialized
SGI XFS with EAs, realtime, quota, no debug enabled
i2c-core.o: i2c core module
i2c-dev.o: i2c /dev entries driver module
i2c-core.o: driver i2c-dev dummy driver registered.
i2c-ali15x3.o version 2.6.2 (20011118)
i2c-ali15x3.o: Error: Can't detect ali15x3!
i2c-ali15x3.o: ALI15X3 not detected, module not inserted.
i2c-piix4.o version 2.6.2 (20011118)
i2c-piix4.o: Found CSB5 device
i2c-dev.o: Registered 'SMBus PIIX4 adapter at 3a80' as minor 0
i2c-core.o: adapter SMBus PIIX4 adapter at 3a80 registered as adapter 0.
i2c-piix4.o: SMBus detected and initialized
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI edttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10e
Non-volatile memory driver v1.2
block: 128 slots per queue, batch=32
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ServerWorks CSB5: IDE controller on PCI bus 00 dev 79
ServerWorks CSB5: chipset revision 146
ServerWorks CSB5: native mode: will probe irqs later
ide0: BM-DMA at 0xfcb0-0xfcb7, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xfcb8-0xfcbf, BIOS settings: hdc:DMA, hdd:DMA
hda: ST340016A, SN=3HS4WK9R, FWREV=3.19, ATA DISK drive
ide0 at 0xfcd8-0xfcdf,0xfcd6 on irq 14
hda: 78165360 sectors (40021 MB) w/2048KiB Cache, CHS=77545/16/63, UDMA(66)
Partition check:
hda: hda1 hda2 hda3 hda4
natsemi.c:v1.07 1/9/2001 Written by Donald Becker <becker@scyld.com>
http://www.scyld.com/network/natsemi.html
(unofficial 2.4.x kernel port, version 1.07+LK1.0.15, Jan 14, 2002 Jeff Garz)PCI: Found IRQ 5 for device 01:06.0
eth0: NatSemi DP8381[56] at 0xd0800000, 00:10:e0:06:11:3e, IRQ 5.
PCI: Found IRQ 7 for device 01:07.0
eth1: NatSemi DP8381[56] at 0xd0802000, 00:10:e0:06:13:55, IRQ 7.
SCSI subsystem driver Revision: 1.00
md: linear personality registered as nr 1
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: raid5 personality registered as nr 4
raid5: measuring checksumming speed
8regs : 1392.000 MB/sec
32regs : 908.800 MB/sec
pIII_sse : 2038.000 MB/sec
pII_mmx : 2249.600 MB/sec
p5_mmx : 2391.600 MB/sec
raid5: using function: pIII_sse (2038.000 MB/sec)
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 16384)
eth0: link up.
eth0: Setting full-duplex based on negotiated link capability.
eth1: autonegotiation did not complete in 4000 usec.
Sending DHCP and RARP requests ., OK
IP-Config: Got DHCP answer from 192.168.0.1, my address is 192.168.0.2
IP-Config: Complete:
device=eth0, addr=192.168.0.2, mask=255.255.255.0, gw=255.255.255.255,
host=192.168.0.2, domain=example.org, nis-domain=(none),
bootserver=192.168.0.1, rootserver=192.168.0.1, rootpath=
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Looking up port of RPC 100003/2 on 192.168.0.1
Alors j'ai fait une expérience avec une ip 192.168.1.1 sur eth1:
(eth0 à une ip dchp de la freebox du type 192.168.0.1)
# The loopback network interface
auto lo
iface lo inet loopback
# The primary network interface
auto eth0
iface eth0 inet dhcp
name Carte Ethernet
auto eth1
iface eth1 inet static
name Carte Ethernet
address 192.168.1.1
netmask 255.255.255.0
broadcast 192.168.1.255
network 192.168.1.0
gateway 192.168.1.255
le dhcp3 sur eth1
subnet 192.168.1.0 netmask 255.255.255.0 {
range 192.168.1.100 192.168.1.150
default-lease-time 600;
max-lease-time 7200;
}
host raq550 {
hardware ethernet 00:10:e0:06:11:e3;
fixed-address 192.168.1.2;
}
et là, par ma grande surprise sa fonctionne, mais au niveau de la console du minicom pour l'install debian à l'aide de debootstrap, j'ai un message d'erreur, pas d'acces sur internet par eth0 !!!!
tu serais me dire d'ou sa vien ???
Message édité par Mal1cia le 05-04-2007 à 20:30:10
