voila quand je fais un grep audio /proc/pci le systeme me met que j'ai cette carte son
Multimedia audio controller: C-Media Electronics Inc CM8738 (rev 16).
Ensuite quand je mets
alias snd-card-0 snd-cmi8738
dans le /etc/modules.d/alsa et que je relance alsa il me met
modprobe: Can't locate module snd-cmi8738
Or j ai compile l'ensemble des drivers alsa donc j'aimerai savoir ce qui ne va pas

http://www.alsa-project.org/alsa-d [...] ule=cmipci
 
modprobe snd-cmipci
modprobe snd-pcm-oss
modprobe snd-mixer-oss
modprobe snd-seq-oss

quand je fais modprobe snd-cmipci y me met ca :
/lib/modules/2.4.20-gentoo-r6/kernel/sound/pci/snd-cmipci.o: init_module: No suc
Hint: insmod errors can be caused by incorrect module parameters, including inva
      You may find more information in syslog or the output from dmesg
/lib/modules/2.4.20-gentoo-r6/kernel/sound/pci/snd-cmipci.o: insmod /lib/modules
/lib/modules/2.4.20-gentoo-r6/kernel/sound/pci/snd-cmipci.o: insmod snd-cmipci f

Avec les messages d'erreur complets ça pourrait être plus facile. lol
Je suppose que c'est "No such..." ?
"including invalid..." ?
 
tu les as coupé parce qu'ils sont trop longs ?

/lib/modules/2.4.20-gentoo-r6/kernel/sound/pci/snd-cmipci.o: init_module: No such device
Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters.
      You may find more information in syslog or the output from dmesg
/lib/modules/2.4.20-gentoo-r6/kernel/sound/pci/snd-cmipci.o: insmod /lib/modules/2.4.20-gentoo-r6/kernel/sound/pci/snd-cmipci.o failed
/lib/modules/2.4.20-gentoo-r6/kernel/sound/pci/snd-cmipci.o: insmod snd-cmipci failed
 
oups avait pas vu, voila le message en entier

décharge le module précédent  
 
modprobe -r sound

ca fait toujours pareil  

lsmod
 
lspci

lsmod :
 
Module                  Size  Used by    Tainted: PF
snd-pcm-oss            34756   0  (unused)
snd-pcm                53632   0  [snd-pcm-oss]
snd-page-alloc          5748   0  [snd-pcm]
snd-mixer-oss          10992   0  [snd-pcm-oss]
snd-seq-oss            24192   0  (unused)
snd-seq-midi-event      3264   0  [snd-seq-oss]
snd-seq                30448   2  [snd-seq-oss snd-seq-midi-event]
snd-timer              12644   0  [snd-pcm snd-seq]
snd-seq-device          3776   0  [snd-seq-oss snd-seq]
snd                    28260   0  [snd-pcm-oss snd-pcm snd-mixer-oss snd-seq-oss snd-seq-midi-event snd-seq snd-timer snd-seq-device]
floppy                 47036   0  (autoclean)
nvidia               1538016  10  (autoclean)
ppp_synctty             5792   0  (unused)
ppp_async               7264   1
ppp_generic            14748   3  [ppp_synctty ppp_async]
slhc                    4848   0  [ppp_generic]
8139too                14152   1
mii                     2160   0  [8139too]
cmpci                  25048   0
soundcore               3364   4  [snd cmpci]
nls_iso8859-1           2780   1  (autoclean)
nls_cp437               4316   1  (autoclean)
vfat                    9324   1  (autoclean)
fat                    29816   0  (autoclean) [vfat]
usb-storage            55608   0  (unused)
hid                    12468   0  (unused)
usb-ohci               17152   0  (unused)
usbcore                55264   1  [usb-storage hid usb-ohci]
 
 
lspci :
 
00:00.0 Host bridge: Silicon Integrated Systems [SiS] 735 Host (rev 01)
00:01.0 PCI bridge: Silicon Integrated Systems [SiS] SiS 530 Virtual PCI-to-PCI bridge (AGP)
00:02.0 ISA bridge: Silicon Integrated Systems [SiS] 85C503/5513
00:02.2 USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller (rev 07)
00:02.3 USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller (rev 07)
00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev d0)
00:0d.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
00:11.0 Multimedia audio controller: C-Media Electronics Inc CM8738 (rev 10)
01:00.0 VGA compatible controller: nVidia Corporation NV25 [GeForce4 Ti 4200] (rev a3)

y a personne qui sait alors ?

Tu as en fait le meme problème que moi que je n'ai jamais réussi à résoudre
 
http://forum.hardware.fr/forum2.ph [...] 0&subcat=0

Pourtant elle marche bien sous linux car j avais réussi à la faire marcher lors d'un précédente installation. Mais là pas moyen, sui dégouté

Ahh mais toi tu as une PCI en plus, ca devrait être plus facile ...
 
A mon avis, tu dois fournir au modules les paramètres IO et IRQ de ta carte, c'est l'erreur non ? Avec lspci -vv tu devrait avoir ces informations. Pour connaitre les paramètres du module, il faut faire modinfo snd-cmipci.
 
Attention, il me semble que tu confonds snd-cmipci et snd-cmi8738. Tu es sur d'avoir ce dernier module ? Je ne pense pas et donc ton /etc/modules.d/alsa est à modifier ...

le lspci -vv me donne ca :
 
00:00.0 Host bridge: Silicon Integrated Systems [SiS] 735 Host (rev 01)
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
        Latency: 32
        Region 0: Memory at d0000000 (32-bit, non-prefetchable) [size=64M]
        Capabilities: [c0] AGP version 2.0
                Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
                Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP+ GART64- 64bit- FW- Rate=x4
 
00:01.0 PCI bridge: Silicon Integrated Systems [SiS] SiS 530 Virtual PCI-to-PCI bridge (AGP) (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 64
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
        Memory behind bridge: cde00000-cfefffff
        Prefetchable memory behind bridge: bdb00000-cdcfffff
        BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
 
00:02.0 ISA bridge: Silicon Integrated Systems [SiS] 85C503/5513
        Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
 
00:02.2 USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller (rev 07) (prog-if 10 [OHCI])
        Subsystem: Elitegroup Computer Systems: Unknown device 0a14
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 64 (20000ns max), cache line size 08
        Interrupt: pin D routed to IRQ 11
        Region 0: Memory at cfffe000 (32-bit, non-prefetchable) [size=4K]
 
00:02.3 USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller (rev 07) (prog-if 10 [OHCI])
        Subsystem: Elitegroup Computer Systems: Unknown device 0a14
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 64 (20000ns max), cache line size 08
        Interrupt: pin A routed to IRQ 11
        Region 0: Memory at cffff000 (32-bit, non-prefetchable) [size=4K]
 
00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev d0) (prog-if 80 [Master])
        Subsystem: Silicon Integrated Systems [SiS] SiS5513 EIDE Controller (A,B step)
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 128
        Region 4: I/O ports at ff00 [size=16]
 
00:0d.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
        Subsystem: Realtek Semiconductor Co., Ltd. RT8139
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 64 (8000ns min, 16000ns max)
        Interrupt: pin A routed to IRQ 11
        Region 0: I/O ports at dc00 [size=256]
        Region 1: Memory at cfffdf00 (32-bit, non-prefetchable) [size=256]
        Expansion ROM at cffe0000 [disabled] [size=64K]
 
00:11.0 Multimedia audio controller: C-Media Electronics Inc CM8738 (rev 10)
        Subsystem: C-Media Electronics Inc CMI8738/C3DX PCI Audio Device
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 64 (500ns min, 6000ns max)
        Interrupt: pin A routed to IRQ 11
        Region 0: I/O ports at d800 [size=256]
        Capabilities: [c0] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
 
01:00.0 VGA compatible controller: nVidia Corporation NV25 [GeForce4 Ti 4200] (rev a3) (prog-if 00 [VGA])
        Subsystem: Micro-Star International Co., Ltd.: Unknown device 8700
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 248 (1250ns min, 250ns max)
        Interrupt: pin A routed to IRQ 5
        Region 0: Memory at ce000000 (32-bit, non-prefetchable) [size=16M]
        Region 1: Memory at c0000000 (32-bit, prefetchable) [size=128M]
        Region 2: Memory at cdc80000 (32-bit, prefetchable) [size=512K]
        Expansion ROM at cfee0000 [disabled] [size=128K]
        Capabilities: [60] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [44] AGP version 2.0
                Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
                Command: RQ=32 ArqSz=0 Cal=0 SBA- AGP+ GART64- 64bit- FW- Rate=x4
 
 
modinfo snd-cmipci me donne ca :
 
filename:    /lib/modules/2.4.20-gentoo-r6/kernel/sound/pci/snd-cmipci.o
description: "C-Media CMI8x38 PCI"
author:      "Takashi Iwai <tiwai@suse.de>"
license:     "GPL"
parm:        index int array (min = 1, max = 8), description "Index value for C-Media PCI soundcard."
parm:        id string array (min = 1, max = 8), description "ID string for C-Media PCI soundcard."
parm:        enable int array (min = 1, max = 8), description "Enable C-Media PCI soundcard."
parm:        mpu_port long array (min = 1, max = 8), description "MPU-401 port."
parm:        fm_port long array (min = 1, max = 8), description "FM port."
parm:        soft_ac3 long array (min = 1, max = 8), description "Sofware-conversion of raw SPDIF packets (model 033 only)."
 
 
et dans mon /etc/modules.d/alsa j ai ca :
 
# Alsa 0.9.X kernel modules' configuration file.
# $Header: /home/cvsroot/gentoo-x86/media-sound/alsa-utils/files/alsa-modules.conf-rc,v 1.1 2003/08/05 21:07:55 johnm Exp $
 
# ALSA portion
alias char-major-116 snd
# OSS/Free portion
alias char-major-14 soundcore
 
##
## IMPORTANT:
## You need to customise this section for your specific sound card(s)
## and then run `update-modules' command.
## Read alsa-driver's INSTALL file in /usr/share/doc for more info.
##
##  ALSA portion
alias snd-card-0 snd-cmipci
##alias snd-card-1 snd-ens1371
##  OSS/Free portion
## alias sound-slot-0 snd-card-0
## alias sound-slot-1 snd-card-1
##
 
# OSS/Free portion - card #1
alias sound-service-0-0 snd-mixer-oss
alias sound-service-0-1 snd-seq-oss
alias sound-service-0-3 snd-pcm-oss
alias sound-service-0-8 snd-seq-oss
alias sound-service-0-12 snd-pcm-oss
##  OSS/Free portion - card #2
## alias sound-service-1-0 snd-mixer-oss
## alias sound-service-1-3 snd-pcm-oss
## alias sound-service-1-12 snd-pcm-oss
 
alias /dev/mixer snd-mixer-oss
alias /dev/dsp snd-pcm-oss
alias /dev/midi snd-seq-oss
 
# Set this to the correct number of cards.
options snd cards_limit=1
 
 
Si ca peut t aider pour me dire ce qui va pas