Script started on Thu Mar 18 14:32:46 2004
bum:/home/max# smartctl -a /dev/hda
smartctl version 5.26 Copyright (C) 2002-3 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: WDC WD800BB-00CAA0
Serial Number: WD-WMA8E1433111
Firmware Version: 16.06V16
Device is: In smartctl database [for details use: -P show]
ATA Version is: 5
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Thu Mar 18 14:32:56 2004 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity was
suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever been run.
Total time to complete Offline data collection: (3120) seconds.
Offline data collection
capabilities: (0x3b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 58) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 200 180 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0007 104 088 021 Pre-fail Always - 3866
4 Start_Stop_Count 0x0032 099 099 040 Old_age Always - 1247
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 253 051 Pre-fail Always - 0
9 Power_On_Hours 0x0032 090 090 000 Old_age Always - 7889
10 Spin_Retry_Count 0x0013 100 100 051 Pre-fail Always - 0
11 Calibration_Retry_Count 0x0013 100 100 051 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 1021
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0012 200 200 000 Old_age Always - 1
198 Offline_Uncorrectable 0x0012 200 200 000 Old_age Always - 1
199 UDMA_CRC_Error_Count 0x000a 200 253 000 Old_age Always - 18
200 Multi_Zone_Error_Rate 0x0009 200 200 051 Pre-fail Offline - 0
SMART Error Log Version: 1
ATA Error Count: 17 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Timestamp = decimal seconds since the previous disk power-on.
Note: timestamp "wraps" after 2^32 msec = 49.710 days.
Error 17 occurred at disk power-on lifetime: 1059 hours
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 0f 10 00 e0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Timestamp Command/Feature_Name
-- -- -- -- -- -- -- -- --------- --------------------
40 00 01 0f 10 00 e0 00 323.650 READ VERIFY SECTOR(S)
40 00 02 11 10 00 e0 00 323.650 READ VERIFY SECTOR(S)
40 00 02 0f 10 00 e0 00 321.000 READ VERIFY SECTOR(S)
40 00 04 13 10 00 e0 00 320.950 READ VERIFY SECTOR(S)
40 00 04 0f 10 00 e0 00 318.500 READ VERIFY SECTOR(S)
Error 16 occurred at disk power-on lifetime: 1059 hours
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 02 0f 10 00 e0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Timestamp Command/Feature_Name
-- -- -- -- -- -- -- -- --------- --------------------
40 00 02 0f 10 00 e0 00 321.000 READ VERIFY SECTOR(S)
40 00 04 13 10 00 e0 00 320.950 READ VERIFY SECTOR(S)
40 00 04 0f 10 00 e0 00 318.500 READ VERIFY SECTOR(S)
40 00 08 17 10 00 e0 00 318.450 READ VERIFY SECTOR(S)
40 00 08 0f 10 00 e0 00 315.750 READ VERIFY SECTOR(S)
Error 15 occurred at disk power-on lifetime: 1059 hours
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 04 0f 10 00 e0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Timestamp Command/Feature_Name
-- -- -- -- -- -- -- -- --------- --------------------
40 00 04 0f 10 00 e0 00 318.500 READ VERIFY SECTOR(S)
40 00 08 17 10 00 e0 00 318.450 READ VERIFY SECTOR(S)
40 00 08 0f 10 00 e0 00 315.750 READ VERIFY SECTOR(S)
40 00 10 0f 10 00 e0 00 313.250 READ VERIFY SECTOR(S)
40 00 10 ff 0f 00 e0 00 313.250 READ VERIFY SECTOR(S)
Error 14 occurred at disk power-on lifetime: 1059 hours
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 0f 10 00 e0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Timestamp Command/Feature_Name
-- -- -- -- -- -- -- -- --------- --------------------
40 00 08 0f 10 00 e0 00 315.750 READ VERIFY SECTOR(S)
40 00 10 0f 10 00 e0 00 313.250 READ VERIFY SECTOR(S)
40 00 10 ff 0f 00 e0 00 313.250 READ VERIFY SECTOR(S)
40 00 20 1f 10 00 e0 00 313.250 READ VERIFY SECTOR(S)
40 00 20 ff 0f 00 e0 00 310.600 READ VERIFY SECTOR(S)
Error 13 occurred at disk power-on lifetime: 1059 hours
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 10 0f 10 00 e0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Timestamp Command/Feature_Name
-- -- -- -- -- -- -- -- --------- --------------------
40 00 10 0f 10 00 e0 00 313.250 READ VERIFY SECTOR(S)
40 00 10 ff 0f 00 e0 00 313.250 READ VERIFY SECTOR(S)
40 00 20 1f 10 00 e0 00 313.250 READ VERIFY SECTOR(S)
40 00 20 ff 0f 00 e0 00 310.600 READ VERIFY SECTOR(S)
40 00 40 ff 0f 00 e0 00 308.200 READ VERIFY SECTOR(S)
SMART Self-test log structure revision number 1
No self-tests have been logged. [Use the smartctl -t option to run these.]
bum:/home/max# Script done on Thu Mar 18 14:33:08 2004
|