jaymzwise | Salut,
Je tourne sous Debian Lenny, Kernel 2.6.22-3-amd64.
Lors du lancement, plus particulièrement lors du montage des partitions système, j'ai un arrêt.
Je dois faire un CTRL+C pour que le démarrage continue.
Il arrive que l'arrêt se fasse juste après la détection des ports USB.
Voici ce que j'obtiens avec un dmesg :
Code :
- Linux version 2.6.22-3-amd64 (Debian 2.6.22-6) (maks@debian.org) (gcc version 4.1.3 20071019 (prerelease) (Debian 4.1.2-17)) #1 SMP Sun Nov 4 18:18:09 UTC 2007
- Command line: root=/dev/hda1 ro quiet
- BIOS-provided physical RAM map:
- BIOS-e820: 0000000000000000 - 000000000009f400 (usable)
- BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved)
- BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
- BIOS-e820: 0000000000100000 - 000000007fef0000 (usable)
- BIOS-e820: 000000007fef0000 - 000000007fef3000 (ACPI NVS)
- BIOS-e820: 000000007fef3000 - 000000007ff00000 (ACPI data)
- BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved)
- BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
- Entering add_active_range(0, 0, 159) 0 entries of 3200 used
- Entering add_active_range(0, 256, 524016) 1 entries of 3200 used
- end_pfn_map = 1048576
- DMI 2.3 present.
- ACPI: RSDP 000F7DA0, 0014 (r0 Nvidia)
- ACPI: RSDT 7FEF3040, 0030 (r1 Nvidia AWRDACPI 42302E31 AWRD 0)
- ACPI: FACP 7FEF30C0, 0074 (r1 Nvidia AWRDACPI 42302E31 AWRD 0)
- ACPI: DSDT 7FEF3180, 9C86 (r1 NVIDIA AWRDACPI 1000 MSFT 100000E)
- ACPI: FACS 7FEF0000, 0040
- ACPI: MCFG 7FEFCF40, 003C (r1 Nvidia AWRDACPI 42302E31 AWRD 0)
- ACPI: APIC 7FEFCE80, 0072 (r1 Nvidia AWRDACPI 42302E31 AWRD 0)
- Scanning NUMA topology in Northbridge 24
- No NUMA configuration found
- Faking a node at 0000000000000000-000000007fef0000
- Entering add_active_range(0, 0, 159) 0 entries of 3200 used
- Entering add_active_range(0, 256, 524016) 1 entries of 3200 used
- Bootmem setup node 0 0000000000000000-000000007fef0000
- Zone PFN ranges:
- DMA 0 -> 4096
- DMA32 4096 -> 1048576
- Normal 1048576 -> 1048576
- early_node_map[2] active PFN ranges
- 0: 0 -> 159
- 0: 256 -> 524016
- On node 0 totalpages: 523919
- DMA zone: 56 pages used for memmap
- DMA zone: 1020 pages reserved
- DMA zone: 2923 pages, LIFO batch:0
- DMA32 zone: 7108 pages used for memmap
- DMA32 zone: 512812 pages, LIFO batch:31
- Normal zone: 0 pages used for memmap
- Nvidia board detected. Ignoring ACPI timer override.
- If you got timer trouble try acpi_use_timer_override
- ACPI: PM-Timer IO Port: 0x1008
- ACPI: Local APIC address 0xfee00000
- ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
- Processor #0 (Bootup-CPU)
- ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
- Processor #1
- ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
- ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
- ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
- IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
- ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
- ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
- ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
- ACPI: IRQ9 used by override.
- ACPI: IRQ14 used by override.
- ACPI: IRQ15 used by override.
- Setting APIC routing to flat
- Using ACPI (MADT) for SMP configuration information
- swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
- swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000f0000
- swsusp: Registered nosave memory region: 00000000000f0000 - 0000000000100000
- Allocating PCI resources starting at 80000000 (gap: 7ff00000:70100000)
- SMP: Allowing 2 CPUs, 0 hotplug CPUs
- PERCPU: Allocating 37896 bytes of per cpu data
- Built 1 zonelists. Total pages: 515735
- Kernel command line: root=/dev/hda1 ro quiet
- Initializing CPU#0
- PID hash table entries: 4096 (order: 12, 32768 bytes)
- Marking TSC unstable due to TSCs unsynchronized
- time.c: Detected 2411.143 MHz processor.
- Console: colour VGA+ 80x25
- Checking aperture...
- CPU 0: aperture @ 4c90000000 size 32 MB
- Aperture too small (32 MB)
- No AGP bridge found
- Memory: 2056796k/2096064k available (2008k kernel code, 38880k reserved, 945k data, 296k init)
- Calibrating delay using timer specific routine.. 4826.10 BogoMIPS (lpj=9652216)
- Security Framework v1.0.0 initialized
- SELinux: Disabled at boot.
- Capability LSM initialized
- Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
- Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
- Mount-cache hash table entries: 256
- CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
- CPU: L2 Cache: 512K (64 bytes/line)
- CPU 0/0 -> Node 0
- CPU: Physical Processor ID: 0
- CPU: Processor Core ID: 0
- SMP alternatives: switching to UP code
- ACPI: Core revision 20070126
- Using local APIC timer interrupts.
- result 12558048
- Detected 12.558 MHz APIC timer.
- SMP alternatives: switching to SMP code
- Booting processor 1/2 APIC 0x1
- Initializing CPU#1
- Calibrating delay using timer specific routine.. 4822.64 BogoMIPS (lpj=9645291)
- CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
- CPU: L2 Cache: 512K (64 bytes/line)
- CPU 1/1 -> Node 0
- CPU: Physical Processor ID: 0
- CPU: Processor Core ID: 1
- AMD Athlon(tm) 64 X2 Dual Core Processor 4600+ stepping 02
- Brought up 2 CPUs
- migration_cost=260
- NET: Registered protocol family 16
- ACPI: bus type pci registered
- PCI: Using MMCONFIG at f0000000 - ffffffff
- PCI: No mmconfig possible on device 00:18
- ACPI: Interpreter enabled
- ACPI: (supports S0 S1 S3 S4 S5)
- ACPI: Using IOAPIC for interrupt routing
- ACPI: PCI Root Bridge [PCI0] (0000:00)
- PCI: Probing PCI hardware (bus 00)
- PCI: Transparent bridge - 0000:00:06.0
- ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
- ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
- ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 10 11 14 15) *0, disabled.
- ACPI: PCI Interrupt Link [LNK2] (IRQs 5 7 9 10 11 14 15) *0, disabled.
- ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 9 10 11 14 15) *0, disabled.
- ACPI: PCI Interrupt Link [LNK4] (IRQs *5 7 9 10 11 14 15)
- ACPI: PCI Interrupt Link [LNK5] (IRQs 5 7 9 10 11 14 15) *0, disabled.
- ACPI: PCI Interrupt Link [LNK6] (IRQs 5 7 9 *10 11 14 15)
- ACPI: PCI Interrupt Link [LNK7] (IRQs 5 7 9 10 *11 14 15)
- ACPI: PCI Interrupt Link [LNK8] (IRQs 5 7 9 10 11 14 15) *0, disabled.
- ACPI: PCI Interrupt Link [LP2P] (IRQs 5 7 9 10 11 14 15) *0, disabled.
- ACPI: PCI Interrupt Link [LUBA] (IRQs 5 7 9 *10 11 14 15)
- ACPI: PCI Interrupt Link [LMAC] (IRQs 5 7 9 *10 11 14 15)
- ACPI: PCI Interrupt Link [LMC1] (IRQs 5 7 9 *10 11 14 15)
- ACPI: PCI Interrupt Link [LAZA] (IRQs *5 7 9 10 11 14 15)
- ACPI: PCI Interrupt Link [LPMU] (IRQs 5 7 9 10 11 14 15) *0, disabled.
- ACPI: PCI Interrupt Link [LSMB] (IRQs *5 7 9 10 11 14 15)
- ACPI: PCI Interrupt Link [LUB2] (IRQs 5 7 9 10 *11 14 15)
- ACPI: PCI Interrupt Link [LIDE] (IRQs 5 7 9 10 11 14 15) *0, disabled.
- ACPI: PCI Interrupt Link [LSID] (IRQs 5 7 9 10 *11 14 15)
- ACPI: PCI Interrupt Link [LFID] (IRQs *5 7 9 10 11 14 15)
- ACPI: PCI Interrupt Link [LSA2] (IRQs 5 7 9 *10 11 14 15)
- ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
- ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
- ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
- ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0
- ACPI: PCI Interrupt Link [APC5] (IRQs 16) *0, disabled.
- ACPI: PCI Interrupt Link [APC6] (IRQs 16) *0
- ACPI: PCI Interrupt Link [APC7] (IRQs 16) *0
- ACPI: PCI Interrupt Link [APC8] (IRQs 16) *0, disabled.
- ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0
- ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0
- ACPI: PCI Interrupt Link [AMC1] (IRQs 20 21 22 23) *0
- ACPI: PCI Interrupt Link [APMU] (IRQs 20 21 22 23) *0, disabled.
- ACPI: PCI Interrupt Link [AAZA] (IRQs 20 21 22 23) *0
- ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0
- ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0
- ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled.
- ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
- ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0
- ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0
- ACPI: PCI Interrupt Link [ASA2] (IRQs 20 21 22 23) *0
- Linux Plug and Play Support v0.97 (c) Adam Belay
- pnp: PnP ACPI init
- ACPI: bus type pnp registered
- pnp: ACPI device : hid PNP0A08
- pnp: ACPI device : hid PNP0C02
- pnp: ACPI device : hid PNP0C02
- pnp: ACPI device : hid PNP0200
- pnp: ACPI device : hid PNP0B00
- pnp: ACPI device : hid PNP0800
- pnp: ACPI device : hid PNP0C04
- pnp: ACPI device : hid PNP0700
- pnp: ACPI device : hid PNP0501
- pnp: ACPI device : hid PNP0400
- pnp: ACPI device : hid PNP0F13
- pnp: ACPI device : hid PNP0303
- pnp: ACPI device : hid PNP0C02
- pnp: ACPI device : hid PNP0C01
- pnp: PnP ACPI: found 14 devices
- ACPI: ACPI bus type pnp unregistered
- usbcore: registered new interface driver usbfs
- usbcore: registered new interface driver hub
- usbcore: registered new device driver usb
- PCI: Using ACPI for IRQ routing
- PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
- NET: Registered protocol family 8
- NET: Registered protocol family 20
- ACPI: RTC can wake from S4
- pnp: the driver 'system' has been registered
- pnp: match found with the PnP device '00:01' and the driver 'system'
- pnp: 00:01: ioport range 0x1000-0x107f has been reserved
- pnp: 00:01: ioport range 0x1080-0x10ff has been reserved
- pnp: 00:01: ioport range 0x1400-0x147f has been reserved
- pnp: 00:01: ioport range 0x1480-0x14ff has been reserved
- pnp: 00:01: ioport range 0x1800-0x187f has been reserved
- pnp: 00:01: ioport range 0x1880-0x18ff has been reserved
- pnp: match found with the PnP device '00:02' and the driver 'system'
- pnp: match found with the PnP device '00:0c' and the driver 'system'
- pnp: 00:0c: iomem range 0x0-0x0 could not be reserved
- pnp: match found with the PnP device '00:0d' and the driver 'system'
- pnp: 00:0d: iomem range 0xd0000-0xd3fff has been reserved
- pnp: 00:0d: iomem range 0xd8800-0xdbfff has been reserved
- pnp: 00:0d: iomem range 0xf0000-0xfbfff could not be reserved
- pnp: 00:0d: iomem range 0xfc000-0xfffff could not be reserved
- PCI: Bridge: 0000:00:06.0
- IO window: disabled.
- MEM window: fde00000-fdefffff
- PREFETCH window: disabled.
- PCI: Bridge: 0000:00:0a.0
- IO window: disabled.
- MEM window: disabled.
- PREFETCH window: disabled.
- PCI: Bridge: 0000:00:0b.0
- IO window: disabled.
- MEM window: disabled.
- PREFETCH window: disabled.
- PCI: Bridge: 0000:00:0c.0
- IO window: disabled.
- MEM window: disabled.
- PREFETCH window: disabled.
- PCI: Bridge: 0000:00:0d.0
- IO window: disabled.
- MEM window: disabled.
- PREFETCH window: disabled.
- PCI: Bridge: 0000:00:0e.0
- IO window: 9000-afff
- MEM window: fdd00000-fddfffff
- PREFETCH window: disabled.
- PCI: Bridge: 0000:08:00.0
- IO window: 8000-8fff
- MEM window: f9000000-fbffffff
- PREFETCH window: e0000000-efffffff
- PCI: Bridge: 0000:08:01.0
- IO window: 7000-7fff
- MEM window: f6000000-f8ffffff
- PREFETCH window: d0000000-dfffffff
- PCI: Bridge: 0000:07:00.0
- IO window: 7000-8fff
- MEM window: f6000000-fbffffff
- PREFETCH window: d0000000-efffffff
- PCI: Bridge: 0000:00:0f.0
- IO window: 7000-8fff
- MEM window: f6000000-fcffffff
- PREFETCH window: d0000000-efffffff
- PCI: Setting latency timer of device 0000:00:06.0 to 64
- PCI: Setting latency timer of device 0000:00:0a.0 to 64
- PCI: Setting latency timer of device 0000:00:0b.0 to 64
- PCI: Setting latency timer of device 0000:00:0c.0 to 64
- PCI: Setting latency timer of device 0000:00:0d.0 to 64
- PCI: Setting latency timer of device 0000:00:0e.0 to 64
- PCI: Setting latency timer of device 0000:00:0f.0 to 64
- PCI: Setting latency timer of device 0000:07:00.0 to 64
- PCI: Setting latency timer of device 0000:08:00.0 to 64
- PCI: Setting latency timer of device 0000:08:01.0 to 64
- NET: Registered protocol family 2
- Time: acpi_pm clocksource has been installed.
- IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
- TCP established hash table entries: 262144 (order: 10, 6291456 bytes)
- TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
- TCP: Hash tables configured (established 262144 bind 65536)
- TCP reno registered
- checking if image is initramfs... it is
- Freeing initrd memory: 5936k freed
- audit: initializing netlink socket (disabled)
- audit(1200311635.680:1): initialized
- VFS: Disk quotas dquot_6.5.1
- Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
- io scheduler noop registered
- io scheduler anticipatory registered
- io scheduler deadline registered
- io scheduler cfq registered (default)
- Boot video device is 0000:0a:00.0
- PCI: Setting latency timer of device 0000:00:0a.0 to 64
- assign_interrupt_mode Found MSI capability
- Allocate Port Service[0000:00:0a.0:pcie00]
- Allocate Port Service[0000:00:0a.0:pcie03]
- PCI: Setting latency timer of device 0000:00:0b.0 to 64
- assign_interrupt_mode Found MSI capability
- Allocate Port Service[0000:00:0b.0:pcie00]
- Allocate Port Service[0000:00:0b.0:pcie03]
- PCI: Setting latency timer of device 0000:00:0c.0 to 64
- assign_interrupt_mode Found MSI capability
- Allocate Port Service[0000:00:0c.0:pcie00]
- Allocate Port Service[0000:00:0c.0:pcie03]
- PCI: Setting latency timer of device 0000:00:0d.0 to 64
- assign_interrupt_mode Found MSI capability
- Allocate Port Service[0000:00:0d.0:pcie00]
- Allocate Port Service[0000:00:0d.0:pcie03]
- PCI: Setting latency timer of device 0000:00:0e.0 to 64
- assign_interrupt_mode Found MSI capability
- Allocate Port Service[0000:00:0e.0:pcie00]
- Allocate Port Service[0000:00:0e.0:pcie03]
- PCI: Setting latency timer of device 0000:00:0f.0 to 64
- assign_interrupt_mode Found MSI capability
- Allocate Port Service[0000:00:0f.0:pcie00]
- Allocate Port Service[0000:00:0f.0:pcie03]
- PCI: Setting latency timer of device 0000:07:00.0 to 64
- Allocate Port Service[0000:07:00.0:pcie10]
- PCI: Setting latency timer of device 0000:08:00.0 to 64
- Allocate Port Service[0000:08:00.0:pcie20]
- PCI: Setting latency timer of device 0000:08:01.0 to 64
- Allocate Port Service[0000:08:01.0:pcie20]
- Real Time Clock Driver v1.12ac
- Linux agpgart interface v0.102 (c) Dave Jones
- Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
- serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
- pnp: the driver 'serial' has been registered
- pnp: match found with the PnP device '00:08' and the driver 'serial'
- 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
- RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
- pnp: the driver 'i8042 kbd' has been registered
- pnp: match found with the PnP device '00:0b' and the driver 'i8042 kbd'
- pnp: the driver 'i8042 aux' has been registered
- pnp: match found with the PnP device '00:0a' and the driver 'i8042 aux'
- PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
- serio: i8042 KBD port at 0x60,0x64 irq 1
- serio: i8042 AUX port at 0x60,0x64 irq 12
- mice: PS/2 mouse device common for all mice
- TCP bic registered
- NET: Registered protocol family 1
- NET: Registered protocol family 17
- Freeing unused kernel memory: 296k freed
- input: AT Translated Set 2 keyboard as /class/input/input0
- ACPI: Fan [FAN] (on)
- ACPI: Thermal Zone [THRM] (40 C)
- SCSI subsystem initialized
- libata version 2.21 loaded.
- sata_nv 0000:00:05.0: version 3.4
- ACPI: PCI Interrupt Link [APSI] enabled at IRQ 23
- ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [APSI] -> GSI 23 (level, low) -> IRQ 23
- PCI: Setting latency timer of device 0000:00:05.0 to 64
- scsi0 : sata_nv
- scsi1 : sata_nv
- ata1: SATA max UDMA/133 cmd 0x00000000000109f0 ctl 0x0000000000010bf2 bmdma 0x000000000001e000 irq 23
- ata2: SATA max UDMA/133 cmd 0x0000000000010970 ctl 0x0000000000010b72 bmdma 0x000000000001e008 irq 23
- forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.60.
- ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
- Floppy drive(s): fd0 is 1.44M
- FDC 0 is a post-1991 82077
- ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
- ata1.00: ATA-7: SAMSUNG SP2504C, VT100-41, max UDMA7
- ata1.00: 488397168 sectors, multi 1: LBA48 NCQ (depth 0/32)
- ata1.00: configured for UDMA/133
- ata2: SATA link down (SStatus 0 SControl 300)
- scsi 0:0:0:0: Direct-Access ATA SAMSUNG SP2504C VT10 PQ: 0 ANSI: 5
- ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 22
- ACPI: PCI Interrupt 0000:00:05.1[B] -> Link [APSJ] -> GSI 22 (level, low) -> IRQ 22
- PCI: Setting latency timer of device 0000:00:05.1 to 64
- scsi2 : sata_nv
- scsi3 : sata_nv
- ata3: SATA max UDMA/133 cmd 0x00000000000109e0 ctl 0x0000000000010be2 bmdma 0x000000000001cc00 irq 22
- ata4: SATA max UDMA/133 cmd 0x0000000000010960 ctl 0x0000000000010b62 bmdma 0x000000000001cc08 irq 22
- ata3: SATA link down (SStatus 0 SControl 300)
- ata4: SATA link down (SStatus 0 SControl 300)
- ACPI: PCI Interrupt Link [ASA2] enabled at IRQ 21
- ACPI: PCI Interrupt 0000:00:05.2[C] -> Link [ASA2] -> GSI 21 (level, low) -> IRQ 21
- PCI: Setting latency timer of device 0000:00:05.2 to 64
- scsi4 : sata_nv
- scsi5 : sata_nv
- ata5: SATA max UDMA/133 cmd 0x000000000001c800 ctl 0x000000000001c402 bmdma 0x000000000001b800 irq 21
- ata6: SATA max UDMA/133 cmd 0x000000000001c000 ctl 0x000000000001bc02 bmdma 0x000000000001b808 irq 21
- ata5: SATA link down (SStatus 0 SControl 300)
- ata6: SATA link down (SStatus 0 SControl 300)
- ACPI: PCI Interrupt Link [APCF] enabled at IRQ 20
- ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 20 (level, low) -> IRQ 20
- PCI: Setting latency timer of device 0000:00:02.0 to 64
- ohci_hcd 0000:00:02.0: OHCI Host Controller
- ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
- ohci_hcd 0000:00:02.0: irq 20, io mem 0xfe02f000
- usb usb1: configuration #1 chosen from 1 choice
- hub 1-0:1.0: USB hub found
- hub 1-0:1.0: 10 ports detected
- ahci 0000:06:00.0: version 2.2
- ACPI: PCI Interrupt Link [APC7] enabled at IRQ 16
- ACPI: PCI Interrupt 0000:06:00.0[A] -> Link [APC7] -> GSI 16 (level, low) -> IRQ 16
- Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
- ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
- pnp: the driver 'ide' has been registered
- usb 1-1: new low speed USB device using ohci_hcd and address 2
- usb 1-1: configuration #1 chosen from 1 choice
- usb 1-2: new full speed USB device using ohci_hcd and address 3
- ahci 0000:06:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x3 impl SATA mode
- ahci 0000:06:00.0: flags: 64bit ncq pm led clo pmp pio slum part
- PCI: Setting latency timer of device 0000:06:00.0 to 64
- scsi6 : ahci
- scsi7 : ahci
- ata7: SATA max UDMA/133 cmd 0xffffc2000032c100 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 16
- ata8: SATA max UDMA/133 cmd 0xffffc2000032c180 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 16
- usb 1-2: configuration #1 chosen from 1 choice
- ata7: SATA link down (SStatus 0 SControl 300)
- usb 1-3: new full speed USB device using ohci_hcd and address 4
- usb 1-3: configuration #1 chosen from 1 choice
- usbcore: registered new interface driver hiddev
- input: Guillemot Corporation DA Leader as /class/input/input1
- input: USB HID v1.00 Gamepad [Guillemot Corporation DA Leader] on usb-0000:00:02.0-1
- usbcore: registered new interface driver usbhid
- drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
- ata8: SATA link down (SStatus 0 SControl 300)
- ACPI: PCI Interrupt Link [APCH] enabled at IRQ 23
- ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [APCH] -> GSI 23 (level, low) -> IRQ 23
- PCI: Setting latency timer of device 0000:00:08.0 to 64
- forcedeth: using HIGHDMA
- eth0: forcedeth.c: subsystem: 010de:cb84 bound to 0000:00:08.0
- ACPI: PCI Interrupt Link [AMC1] enabled at IRQ 22
- ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [AMC1] -> GSI 22 (level, low) -> IRQ 22
- PCI: Setting latency timer of device 0000:00:09.0 to 64
- forcedeth: using HIGHDMA
- eth1: forcedeth.c: subsystem: 010de:cb84 bound to 0000:00:09.0
- NFORCE-MCP55: IDE controller at PCI slot 0000:00:04.0
- NFORCE-MCP55: chipset revision 161
- NFORCE-MCP55: not 100% native mode: will probe irqs later
- NFORCE-MCP55: 0000:00:04.0 (rev a1) UDMA133 controller
- ide0: BM-DMA at 0xf400-0xf407, BIOS settings: hda:DMA, hdb:DMA
- Probing IDE interface ide0...
- ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
- ACPI: PCI Interrupt 0000:01:0b.0[A] -> Link [APC4] -> GSI 19 (level, low) -> IRQ 19
- firewire_ohci: Added fw-ohci device 0000:01:0b.0, OHCI version 1.10
- hda: WDC WD2000JB-00GVC0, ATA DISK drive
- firewire_core: created new fw device fw0 (0 config rom retries)
- hdb: _NEC DVD_RW ND-3540A, ATAPI CD/DVD-ROM drive
- ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
- ACPI: PCI Interrupt Link [APCL] enabled at IRQ 21
- ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCL] -> GSI 21 (level, low) -> IRQ 21
- PCI: Setting latency timer of device 0000:00:02.1 to 64
- ehci_hcd 0000:00:02.1: EHCI Host Controller
- ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
- ehci_hcd 0000:00:02.1: debug port 1
- PCI: cache line size of 64 is not supported by device 0000:00:02.1
- ehci_hcd 0000:00:02.1: irq 21, io mem 0xfe02e000
- ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
- usb usb2: configuration #1 chosen from 1 choice
- hub 2-0:1.0: USB hub found
- hub 2-0:1.0: 10 ports detected
- usb 1-1: USB disconnect, address 2
- JMB363: IDE controller at PCI slot 0000:06:00.1
- PCI: Enabling device 0000:06:00.1 (0000 -> 0001)
- ACPI: PCI Interrupt Link [APC8] enabled at IRQ 16
- ACPI: PCI Interrupt 0000:06:00.1[B] -> Link [APC8] -> GSI 16 (level, low) -> IRQ 16
- JMB363: chipset revision 2
- JMB363: 100% native mode on irq 16
- PCI: Setting latency timer of device 0000:06:00.1 to 64
- ide1: BM-DMA at 0x9c00-0x9c07, BIOS settings: hdc:pio, hdd:pio
- ide2: BM-DMA at 0x9c08-0x9c0f, BIOS settings: hde:pio, hdf:pio
- Probing IDE interface ide1...
- usb 1-2: USB disconnect, address 3
- hdb: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
- Uniform CD-ROM driver Revision: 3.20
- sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
- sd 0:0:0:0: [sda] Write Protect is off
- sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
- sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
- sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
- sd 0:0:0:0: [sda] Write Protect is off
- sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
- sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
- sda: unknown partition table
- sd 0:0:0:0: [sda] Attached SCSI disk
- hda: max request size: 512KiB
- hda: 390721968 sectors (200049 MB) w/8192KiB Cache, CHS=24321/255/63, UDMA(33)
- hda: cache flushes supported
- hda: hda1 hda2 < hda5 hda6 hda7 hda8 hda9 hda10 hda11<6>usb 1-3: USB disconnect, address 4
- hda12 >
- Probing IDE interface ide2...
- usb 1-1: new low speed USB device using ohci_hcd and address 5
- Attempting manual resume
- swsusp: Marking nosave pages: 000000000009f000 - 0000000000100000
- swsusp: Basic memory bitmaps created
- swsusp: Basic memory bitmaps freed
- kjournald starting. Commit interval 5 seconds
- EXT3-fs: mounted filesystem with ordered data mode.
- usb 1-1: configuration #1 chosen from 1 choice
- input: Guillemot Corporation DA Leader as /class/input/input2
- input: USB HID v1.00 Gamepad [Guillemot Corporation DA Leader] on usb-0000:00:02.0-1
- usb 1-2: new full speed USB device using ohci_hcd and address 6
- usb 1-2: configuration #1 chosen from 1 choice
- usb 1-3: new full speed USB device using ohci_hcd and address 7
- usb 1-3: configuration #1 chosen from 1 choice
- i2c-adapter i2c-0: nForce2 SMBus adapter at 0x1c00
- i2c-adapter i2c-1: nForce2 SMBus adapter at 0x1c40
- input: PC Speaker as /class/input/input3
- logips2pp: Detected unknown logitech mouse model 89
- ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 20
- ACPI: PCI Interrupt 0000:00:06.1[B] -> Link [AAZA] -> GSI 20 (level, low) -> IRQ 20
- PCI: Setting latency timer of device 0000:00:06.1 to 64
- usbcore: registered new interface driver snd-usb-audio
- input: ImExPS/2 Logitech Explorer Mouse as /class/input/input4
- pnp: the driver 'parport_pc' has been registered
- pnp: match found with the PnP device '00:09' and the driver 'parport_pc'
- parport_pc 00:09: reported by Plug and Play ACPI
- parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
- Adding 2931820k swap on /dev/hda7. Priority:-1 extents:1 across:2931820k
- EXT3 FS on hda1, internal journal
- loop: module loaded
- device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
- kjournald starting. Commit interval 5 seconds
- EXT3 FS on hda11, internal journal
- EXT3-fs: mounted filesystem with ordered data mode.
- kjournald starting. Commit interval 5 seconds
- EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
- EXT3 FS on sda, internal journal
- EXT3-fs: mounted filesystem with ordered data mode.
- kjournald starting. Commit interval 5 seconds
- EXT3 FS on hda5, internal journal
- EXT3-fs: mounted filesystem with ordered data mode.
- kjournald starting. Commit interval 5 seconds
- EXT3 FS on hda9, internal journal
- EXT3-fs: mounted filesystem with ordered data mode.
- kjournald starting. Commit interval 5 seconds
- EXT3 FS on hda8, internal journal
- EXT3-fs: mounted filesystem with ordered data mode.
- kjournald starting. Commit interval 5 seconds
- EXT3 FS on hda12, internal journal
- EXT3-fs: mounted filesystem with ordered data mode.
- kjournald starting. Commit interval 5 seconds
- EXT3 FS on hda10, internal journal
- EXT3-fs: mounted filesystem with ordered data mode.
- ip_tables: (C) 2000-2006 Netfilter Core Team
- Netfilter messages via NETLINK v0.30.
- nf_conntrack version 0.5.0 (8192 buckets, 65536 max)
- input: Power Button (FF) as /class/input/input5
- ACPI: Power Button (FF) [PWRF]
- input: Power Button (CM) as /class/input/input6
- ACPI: Power Button (CM) [PWRB]
- nvidia: module license 'NVIDIA' taints kernel.
- ACPI: PCI Interrupt Link [APC6] enabled at IRQ 16
- ACPI: PCI Interrupt 0000:09:00.0[A] -> Link [APC6] -> GSI 16 (level, low) -> IRQ 16
- PCI: Setting latency timer of device 0000:09:00.0 to 64
- ACPI: PCI Interrupt 0000:0a:00.0[A] -> Link [APC7] -> GSI 16 (level, low) -> IRQ 16
- PCI: Setting latency timer of device 0000:0a:00.0 to 64
- NVRM: loading NVIDIA UNIX x86_64 Kernel Module 169.07 Thu Dec 13 18:34:01 PST 2007
- FvwmEvent[5142]: segfault at 0000000000000000 rip 00002b6dba70aaec rsp 00007ffff0d74d68 error 4
- FvwmEvent[5145]: segfault at 0000000000000000 rip 00002adde62e3aec rsp 00007fffc519d198 error 4
- NET: Registered protocol family 10
- lo: Disabled Privacy Extensions
- eth1: no IPv6 routers present
- eth0: no IPv6 routers present
|
J'ai constaté que j'avais énormément de ACPI: PCI Interrupt.
Ca sent le problème de carte mère non ?
Message édité par jaymzwise le 14-01-2008 à 13:18:23
|
