dac merci, je pense que je vais utiliser la foscam en local, et enregistrer le flux vidéo (en cas de détection de mouvement) via un des logiciels conseillés par foscam ici:
http://foscam.us/blog/index.php?p=39?
 
Pour ma part je prendrai iSpy (opensource) qui prévient par sms en cas de détection:
http://www.ispyconnect.com/
 
Vous pensez que c'est ok je peux acheter la foscam là pour faire ça? Je viens d'essayer iSpy avec une webcam usb ça marche nickel. Du coup je me demande si ça fonctionnera sur la foscam en wifi si j'indique son IP locale dans iSpy (donc pas besoin de hotspot tout sera en local).
 
Merci encore

I have managed to get permission to release serial interface recovery methods for the FI9821W V1 ("Version 1" ) and have also included some additional files and steps required to recover your FI9821W V1, if your camera has failed during a firmware upgrade. By using the serial interface for the camera.
 
Version 2 of the FI9821W has a WPS button just under the WiFi antenna connector on the outside of the camera. If you don't see the word WPS and a button there. Then your FI9821W is a V1.
 
While these steps may work for a FI9821W V1 that is in a loop, they are intended for cameras that failed while upgrading firmware. The cause could also be a failed hardware component causing the issue, if your camera is failing to boot normally and this did NOT start while upgrading firmware.
 
I am hosting the tools and instructions for this. So, please send me a PM ("Private Message in the Foscam.us forum - See Below for details" ) and I will give you a link to the tools and instructions. Please do NOT copy or distribute these tools and instructions for others. They may change and the download location could change as well.
 
You will need to use the tools included to recover your DDNS and wired MAC Address after using the special firmware installed using the serial interface recovery methods. If you don't do that. Then your Factory DDNS will remain blank and your wired MAC Address will not be correct. The tools and instructions are included to also do these steps as well.
 
Note: When recovering your FI9821W V1 using these tools and methods. If your DDNS was x.myfoscam.org ("On the bottom of the camera" ). There are additional steps and files required to re-flash your DDNS otherwise, during the recovery process your DDNS will be changed to x.myipcamera.org. These additional steps and files are also included and documented in the instructions.  
 
If you need a copy of these tools and instructions or have any questions or know of someone that also needs these instructions? Please send me or have them send me a PM ("Private Message" ) here. You or they, will need to register in the Foscam.us forum to do that:
 
http://foscam.us/forum/member4738.html
 
Please Note: There is now a version 2 (V2) of the FI9821W. These instructions will NOT work for this new hardware version of the FI9821W. It also has a different pin out order and locations for the serial connection then the V1 does. I do also have this pin out order and location information as well for the FI9821W V2, but no serial interface recovery tools or methods yet for the FI9821W V2.
 
Don Kennedy AKA TheUberOverLord

bonjour,
 
-Pour l'accès sur android via FOSCAM viewer, faut il mettre
Http port =8100
Media port = 6100
Est correct?

Bonjour tout le monde,
 
J'ai acheté d'occasion une fi9820w. J'ai réussi à la paramétrer correctement. J'ai installé le dernier firmware : V3.2.6.1.1-20120807
Sur mon lan, aucun problème, j'accède au flux avec vlc en tapant rtsp://user:password@192.168.1.110/11
Je suis derrière une livebox. J'ai créé une DMZ avec l'ip de ma caméra, histoire de ne pas être embêté avec le NAT, comme cela, tous les ports sont bien ouverts et bien mappés. Par contre, quand je suis sur un pc ailleurs que chez moi, au boulot par exemple, je n'arrive pas à visualiser le flux par vlc. Je tape rtsp://admin:pass@ipdemacam/11 et ça ne fonctionne pas.
j'ai ces messages en retour :
 
live555 error: SETUP of'video/H264' failed liveMedia3
live555 error: Nothing to play for rtsp://blablabla.no-ip.org/12
live555 error: TCP rollover failed, aborting�
 
Une idée ? Y'a-t-il un autre moyen de voir le flux à distance via un site web tiers par exemple ?