Replaying journal..
 
The problem has occurred looks like a hardware problem. If you have
bad blocks, we advise you to get a new hard drive, because once you
get one bad block  that the disk  drive internals  cannot hide from
your sight,the chances of getting more are generally said to become
much higher  (precise statistics are unknown to us), and  this disk
drive is probably not expensive enough  for you to you to risk your
time and  data on it.  If you don't want to follow that follow that
advice then  if you have just a few bad blocks,  try writing to the
bad blocks  and see if the drive remaps  the bad blocks (that means
it takes a block  it has  in reserve  and allocates  it for use for
of that block number).  If it cannot remap the block,  use badblock
option (-B) with  reiserfs utils to handle this block correctly.
 
bread: Cannot read the block (213): (Input/output error).

# smartctl -a /dev/hda
smartctl version 5.33 [i686-pc-linux-gnu] Copyright (C) 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
 
=== START OF INFORMATION SECTION ===
Device Model:     ST93015A
Serial Number:    3KW3BRBA
Firmware Version: 4.05
User Capacity:    30,005,821,440 bytes
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   6
ATA Standard is:  ATA/ATAPI-6 T13 1410D revision 2
Local Time is:    Wed Apr 12 18:07:07 2006 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
 
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
 
General SMART Values:
Offline data collection status:  (0x82) Offline data collection activity
                                        was completed without error.
                                        Auto Offline Data Collection: Enabled.
Self-test execution status:      ( 121) The previous self-test completed having
                                        the read element of the test failed.
Total time to complete Offline
data collection:                 ( 426) seconds.
Offline data collection
capabilities:                    (0x5b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        No Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        No General Purpose Logging support.
Short self-test routine
recommended polling time:        (   1) minutes.
Extended self-test routine
recommended polling time:        (  36) minutes.
 
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   063   061   034    Pre-fail  Always       -       35284746
  3 Spin_Up_Time            0x0003   099   098   000    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   100   100   020    Old_age   Always       -       509
  5 Reallocated_Sector_Ct   0x0033   100   100   036    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000f   078   060   030    Pre-fail  Always       -       74586706
  9 Power_On_Hours          0x0032   098   098   000    Old_age   Always       -       2391
 10 Spin_Retry_Count        0x0013   100   100   034    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   020    Old_age   Always       -       574
192 Power-Off_Retract_Count 0x0032   100   100   000    Old_age   Always       -       312
193 Load_Cycle_Count        0x0032   060   060   000    Old_age   Always       -       80291
194 Temperature_Celsius     0x0022   040   056   000    Old_age   Always       -       40
195 Hardware_ECC_Recovered  0x001a   063   061   000    Old_age   Always       -       35284746
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   199   000    Old_age   Always       -       11
200 Multi_Zone_Error_Rate   0x0000   100   253   000    Old_age   Offline      -       0
202 TA_Increase_Count       0x0032   100   253   000    Old_age   Always       -       0
 
SMART Error Log Version: 1
ATA Error Count: 8 (device log contains only the most recent five errors)
        CR = Command Register [HEX]
        FR = Features Register [HEX]
        SC = Sector Count Register [HEX]
        SN = Sector Number Register [HEX]
        CL = Cylinder Low Register [HEX]
        CH = Cylinder High Register [HEX]
        DH = Device/Head Register [HEX]
        DC = Device Command Register [HEX]
        ER = Error register [HEX]
        ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
 
Error 8 occurred at disk power-on lifetime: 2391 hours (99 days + 15 hours)
  When the command that caused the error occurred, the device was active or idle.
 
  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 08 07 00 e0  Error: UNC at LBA = 0x00000708 = 1800
 
  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 2c eb 06 00 e0 00      01:04:38.704  READ DMA EXT
  25 00 2e e9 06 00 e0 00      01:04:38.703  READ DMA EXT
  25 00 30 e7 06 00 e0 00      01:04:38.695  READ DMA EXT
  25 00 30 b7 06 00 e0 00      01:04:38.693  READ DMA EXT
  25 00 30 87 06 00 e0 00      01:04:38.692  READ DMA EXT
 
Error 7 occurred at disk power-on lifetime: 2391 hours (99 days + 15 hours)
  When the command that caused the error occurred, the device was active or idle.
 
  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 08 07 00 e0  Error: UNC at LBA = 0x00000708 = 1800
 
  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 2e e9 06 00 e0 00      01:04:38.704  READ DMA EXT
  25 00 30 e7 06 00 e0 00      01:04:38.703  READ DMA EXT
  25 00 30 b7 06 00 e0 00      01:04:38.695  READ DMA EXT
  25 00 30 87 06 00 e0 00      01:04:38.693  READ DMA EXT
  25 00 30 57 06 00 e0 00      01:04:38.692  READ DMA EXT
 
Error 6 occurred at disk power-on lifetime: 2391 hours (99 days + 15 hours)
  When the command that caused the error occurred, the device was active or idle.
 
  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 08 07 00 e0  Error: UNC at LBA = 0x00000708 = 1800
 
  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 30 e7 06 00 e0 00      01:04:38.704  READ DMA EXT
  25 00 30 b7 06 00 e0 00      01:04:38.703  READ DMA EXT
  25 00 30 87 06 00 e0 00      01:04:38.695  READ DMA EXT
  25 00 30 57 06 00 e0 00      01:04:38.693  READ DMA EXT
  25 00 30 27 06 00 e0 00      01:04:38.692  READ DMA EXT
 
Error 5 occurred at disk power-on lifetime: 2390 hours (99 days + 14 hours)
  When the command that caused the error occurred, the device was active or idle.
 
  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 3d 04 00 e0  Error: UNC at LBA = 0x0000043d = 1085
 
  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 2e 19 04 00 e0 00      00:07:53.842  READ DMA EXT
  25 00 30 17 04 00 e0 00      00:07:53.841  READ DMA EXT
  25 00 30 e7 03 00 e0 00      00:07:53.839  READ DMA EXT
  25 00 30 b7 03 00 e0 00      00:07:53.837  READ DMA EXT
  25 00 30 87 03 00 e0 00      00:07:53.836  READ DMA EXT
 
Error 4 occurred at disk power-on lifetime: 2390 hours (99 days + 14 hours)
  When the command that caused the error occurred, the device was active or idle.
 
  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 3d 04 00 e0  Error: UNC at LBA = 0x0000043d = 1085
 
  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 30 17 04 00 e0 00      00:07:53.842  READ DMA EXT
  25 00 30 e7 03 00 e0 00      00:07:53.841  READ DMA EXT
  25 00 30 b7 03 00 e0 00      00:07:53.839  READ DMA EXT
  25 00 30 87 03 00 e0 00      00:07:53.837  READ DMA EXT
  25 00 30 57 03 00 e0 00      00:07:53.836  READ DMA EXT
 
SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Completed: read failure       90%      2391         1800
 
SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

If it cannot remap the block,  use badblock
option (-B) with  reiserfs utils to handle this block correctly.