Ca existe?
Car celui de kde ne reconnais pas le niveau d'nrj de ma batterie.
Et comme je prefere gnome, il y a rien.
 
Donc un petit programme doit bien exister, non?
 
J'ai une fedore core 1
 
Solution : en Fin de Topic

Dans Gnome, tu as un applet pour ça.
 
Clic droit sur un panel > Ajouter au tableau de bord > Utilitaire > Moniteur de charge de batterie.
 
Sinon il existe aussi wmbattery. Et tu peux aussi faire cat /proc/apm pour connaître le temps restant.

bien vu
 
Mais tu sais pk, sur mon portable, cette utilitaire ( celui de gnome ) ne marche pas, il me marque batterie absente

tu as vérifié que un cat /proc/acpi/battery/BAT0/state te donne des infos correctes ? (enfin sauf si tu as un portable qui date de l'avant guerre et qui ne gére que l'apm ou que l'acpi n'est pas activé dans le noyau...)

La gestion de la batterie dépend de chaque portable et de chaque distrib. Exemple : sur mon IBM, l'apm sous fedora fonctionne à merveille, alors que l'acpi sous MDK 9.2 provoquait des kernel panic.
 
Il faut faire des essais, il n'y a pas de solution miracle...

tout d abord est ce que le module acpi est chargé ??
fait lsmod

fait un dmesg et dit moi si tu vois une ligne avec broken bios detected

houla, vous m'en demandé bcp la    
 
[michael@localhost michael]$ dmesg
Linux version 2.4.22-1.2115.nptl (bhcompile@daffy.perf.redhat.com) (gcc version 3.2.3 20030422 (Red Hat Linux 3.2.3-6)) #1 Wed Oct 29 15:42:51 EST 2003
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009e800 (usable)
 BIOS-e820: 000000000009e800 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000d8000 - 00000000000e0000 (reserved)
 BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000000fef0000 (usable)
 BIOS-e820: 000000000fef0000 - 000000000feff000 (ACPI data)
 BIOS-e820: 000000000feff000 - 000000000ff00000 (ACPI NVS)
 BIOS-e820: 000000000ff00000 - 000000000ff80000 (usable)
 BIOS-e820: 000000000ff80000 - 0000000010000000 (reserved)
 BIOS-e820: 00000000ffb80000 - 00000000ffc00000 (reserved)
 BIOS-e820: 00000000fffffc00 - 0000000100000000 (reserved)
0MB HIGHMEM available.
255MB LOWMEM available.
ACPI: have wakeup address 0xc0001000
On node 0 totalpages: 65408
zone(0): 4096 pages.
zone(1): 61312 pages.
zone(2): 0 pages.
ACPI: RSDP (v000 TOSCPL                                    ) @ 0x000f7020
ACPI: RSDT (v001 TOSCPL   RSDT   0x06040000  LTP 0x00000000) @ 0x0fef9a7f
ACPI: FADT (v001 TOSCPL 888M2    0x06040000 PTL  0x00000001) @ 0x0fefef8c
ACPI: DSDT (v001 TOSCPL ALMADOR  0x06040000 MSFT 0x0100000d) @ 0x00000000
Kernel command line: ro root=LABEL=/ hdc=ide-scsi rhgb
ide_setup: hdc=ide-scsi
Initializing CPU#0
Detected 730.915 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 1458.17 BogoMIPS
Memory: 254700k/261632k available (1503k kernel code, 6476k reserved, 1110k data, 136k init, 0k highmem)
Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU:     After generic, caps: 0383f9ff 00000000 00000000 00000000
CPU:             Common caps: 0383f9ff 00000000 00000000 00000000
CPU: Intel(R) Pentium(R) III Mobile CPU      1000MHz stepping 01
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
ACPI: Subsystem revision 20031002
ACPI: Interpreter disabled.
PCI: PCI BIOS revision 2.10 entry at 0xfd96a, last bus=2
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 00:1f.1
Transparent bridge - Intel Corp. 82801BAM/CAM PCI Bridge
PCI: Using IRQ router PIIX/ICH [8086/248c] at 00:1f.0
PCI: Found IRQ 5 for device 00:1f.1
PCI: Sharing IRQ 5 with 00:1d.2
PCI: Found IRQ 10 for device 02:04.0
PCI: Sharing IRQ 10 with 00:1d.0
PCI: Sharing IRQ 10 with 01:00.0
PCI: Sharing IRQ 10 with 02:00.0
PCI: Found IRQ 10 for device 02:04.1
PCI: Sharing IRQ 10 with 00:1f.3
PCI: Sharing IRQ 10 with 00:1f.5
PCI: Sharing IRQ 10 with 00:1f.6
PCI: Sharing IRQ 10 with 02:01.0
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
pty: 2048 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS1 at 0x02f8 (irq = 3) is a 16550A
PCI: Found IRQ 10 for device 00:1f.6
PCI: Sharing IRQ 10 with 00:1f.3
PCI: Sharing IRQ 10 with 00:1f.5
PCI: Sharing IRQ 10 with 02:01.0
PCI: Sharing IRQ 10 with 02:04.1
Real Time Clock Driver v1.10e
NET4: Frame Diverter 0.46
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH3M: IDE controller at PCI slot 00:1f.1
PCI: Enabling device 00:1f.1 (0005 -> 0007)
PCI: Found IRQ 5 for device 00:1f.1
PCI: Sharing IRQ 5 with 00:1d.2
ICH3M: chipset revision 1
ICH3M: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x1860-0x1867, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0x1868-0x186f, BIOS settings: hdc:DMA, hdd:pio
hda: TOSHIBA MK2018GAP, ATA DISK drive
blk: queue c040cfc0, I/O limit 4095Mb (mask 0xffffffff)
hdc: TOSHIBA DVD-ROM SD-R2102, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 39070080 sectors (20004 MB), CHS=2432/255/63, UDMA(100)
Partition check:
 hda: hda1 hda2 < hda5 hda6 >
ide: late registration of driver.
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 159k freed
VFS: Mounted root (ext2 filesystem).
Journalled Block Device driver loaded
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 136k freed
mice: PS/2 mouse device common for all mice
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 15:50:32 Oct 29 2003
usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 10 for device 00:1d.0
PCI: Sharing IRQ 10 with 01:00.0
PCI: Sharing IRQ 10 with 02:00.0
PCI: Sharing IRQ 10 with 02:04.0
PCI: Setting latency timer of device 00:1d.0 to 64
usb-uhci.c: USB UHCI at I/O 0x1800, IRQ 10
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Found IRQ 5 for device 00:1d.1
PCI: Sharing IRQ 5 with 02:06.0
PCI: Setting latency timer of device 00:1d.1 to 64
usb-uhci.c: USB UHCI at I/O 0x1820, IRQ 5
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Found IRQ 5 for device 00:1d.2
PCI: Sharing IRQ 5 with 00:1f.1
PCI: Setting latency timer of device 00:1d.2 to 64
usb-uhci.c: USB UHCI at I/O 0x1840, IRQ 5
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
hid-core.c: USB HID support drivers
hub.c: new USB device 00:1d.0-1, assigned address 2
input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb1:2.0
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,6), internal journal
Adding Swap: 530104k swap-space (priority -1)
ohci1394: $Rev: 1010 $ Ben Collins <bcollins@debian.org>
PCI: Found IRQ 10 for device 02:00.0
PCI: Sharing IRQ 10 with 00:1d.0
PCI: Sharing IRQ 10 with 01:00.0
PCI: Sharing IRQ 10 with 02:04.0
ohci1394_0: OHCI-1394 1.1 (PCI): IRQ=[10]  MMIO=[d2004000-d20047ff]  Max Packet=[2048]
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00023f2110000a59]
SCSI subsystem driver Revision: 1.00
hdc: attached ide-scsi driver.
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
  Vendor: TOSHIBA   Model: DVD-ROM SD-R2102  Rev: 1015
  Type:   CD-ROM                             ANSI SCSI revision: 02
IA-32 Microcode Update Driver: v1.11 <tigran@veritas.com>
microcode: CPU0 no microcode found! (sig=6b1, pflags=32)
parport0: PC-style at 0x378 [PCSPP,TRISTATE,EPP]
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12
inserting floppy driver for 2.4.22-1.2115.nptl
FDC 0 is a post-1991 82077
8139too Fast Ethernet driver 0.9.26
PCI: Found IRQ 10 for device 02:01.0
PCI: Sharing IRQ 10 with 00:1f.3
PCI: Sharing IRQ 10 with 00:1f.5
PCI: Sharing IRQ 10 with 00:1f.6
PCI: Sharing IRQ 10 with 02:04.1
divert: allocating divert_blk for eth0
eth0: RealTek RTL8139 Fast Ethernet at 0xd0942800, 00:02:3f:74:10:b0, IRQ 10
eth0:  Identified 8139 chip type 'RTL-8100'
divert: freeing divert_blk for eth0
ip_tables: (C) 2000-2002 Netfilter core team
8139too Fast Ethernet driver 0.9.26
PCI: Found IRQ 10 for device 02:01.0
PCI: Sharing IRQ 10 with 00:1f.3
PCI: Sharing IRQ 10 with 00:1f.5
PCI: Sharing IRQ 10 with 00:1f.6
PCI: Sharing IRQ 10 with 02:04.1
divert: allocating divert_blk for eth0
eth0: RealTek RTL8139 Fast Ethernet at 0xd0942800, 00:02:3f:74:10:b0, IRQ 10
eth0:  Identified 8139 chip type 'RTL-8100'
ip_tables: (C) 2000-2002 Netfilter core team
eth0: link down
Linux Kernel Card Services 3.1.22
  options:  [pci] [cardbus] [pm]
PCI: Found IRQ 10 for device 02:04.0
PCI: Sharing IRQ 10 with 00:1d.0
PCI: Sharing IRQ 10 with 01:00.0
PCI: Sharing IRQ 10 with 02:00.0
PCI: Found IRQ 10 for device 02:04.1
PCI: Sharing IRQ 10 with 00:1f.3
PCI: Sharing IRQ 10 with 00:1f.5
PCI: Sharing IRQ 10 with 00:1f.6
PCI: Sharing IRQ 10 with 02:01.0
Yenta IRQ list 0a98, PCI irq10
Socket status: 30000010
Yenta IRQ list 0a98, PCI irq10
Socket status: 30000006
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x378-0x37f 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
ttyS3 at port 0x02e8 (irq = 3) is a 16550A
parport0: PC-style at 0x378 [PCSPP,TRISTATE,EPP]
lp0: using parport0 (polling).
lp0: console ready
Intel 810 + AC97 Audio, version 0.24, 15:50:18 Oct 29 2003
PCI: Found IRQ 10 for device 00:1f.5
PCI: Sharing IRQ 10 with 00:1f.3
PCI: Sharing IRQ 10 with 00:1f.6
PCI: Sharing IRQ 10 with 02:01.0
PCI: Sharing IRQ 10 with 02:04.1
PCI: Setting latency timer of device 00:1f.5 to 64
i810: Intel ICH3 found at IO 0x18c0 and 0x1c00, MEM 0x0000 and 0x0000, IRQ 10
i810_audio: Audio Controller supports 6 channels.
i810_audio: Defaulting to base 2 channel mode.
i810_audio: Resetting connection 0
ac97_codec: AC97 Audio codec, id: CRY52 (Cirrus Logic CS4299 rev D)
i810_audio: AC'97 codec 0 supports AMAP, total channels = 2
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
divert: not allocating divert_blk for non-ethernet device ppp0
PPP Deflate Compression module registered
 
 
 
 
 
 
Par contre le restant ( lsmod et cat /proc/acpi/battery/BAT0/state , pas compris car marche pas dans le terminal )

moi sous suse la batterie est bien reconnu sous mdk non  
 

ca doit etre comme dis plus haut un truc qui n'est pas chargé
 
Et j'ai opté pour une fedora car la mdk ne reconnaissait pas mon modem pcmcia

en root le lsmod devrait marché

 
  j'avais oublié qu'il fallait etre en root
 
non , je vais essayer cela :
 
La gestion de l'énergie est désormais pris en charge par FC1 ; cependant elle n'est pas activée par défaut. Pour l'activer il faut simplement rajouter 'acpi=on' à la séquence de boot.
 
Pour cela, il faut éditer en root le fichier /etc/grub.conf et modifier la ligne suivante :
 
kernel /boot/vmlinuz-2.4.22-1.2115.nptl ro root=LABEL=/ hdc=ide-scsi rhgb
 
ce qui donne :
 
kernel /boot/vmlinuz-2.4.22-1.2115.nptl ro root=LABEL=/ hdc=ide-scsi acpi=on rhgb
 
Voila ! C'est tout ! Vous pouvez alors profiter d'une autonomie de 2 heures environ.

 
 
   
Voila ca marche, il fallait bien rajouter acpi=on a la sequence boot de Grub
Tout est nickel
 
Merci a tous

j'ai un problème avec l'ACPI, de temps en temps il plante au boot avec l'acpi...

 
T'as une fedora ?
Car apriori, il le gere en natif ( je sais pas ce que cela veut dire ) mais apriori, c'est mieux

ca veut dire qu il est né avec

 
Ca veut dire que le noyau est déjà complié pour le supporter.

ca plante seulement en passant l'option au boot (problème de bootsplash qui part en sucette). J'ai 2 entrées dans grub, une avec et une sans et voila...