Besoin d'aide sur un kernel panic

Recherche :

Mot : Pseudo : Filtrer
Bas de page
Auteur	Sujet : Besoin d'aide sur un kernel panic

falcon56

Yop les linuxiens,
Voila j'essaye d'installé en ce moment une debian sur un serveur rack sun cobalt ( pas d'ecran ni de clavier, ni de lecteur dvd )
J'ai donc installé ubuntu sur mon pc principal, crée un dique NFS, fait un debootstrap dessus et démarrer mon cobalt via le reseau
jusque la pas de probleme le cobalt boot bien sur le NFS j'ai le prompt.

Ensuite j'ai partitionné/formaté le disk dur du cobalt monté les disk et deboostraper une nouvelle foix.
Je rentre ensuite en chroot dans mon nouveau system, le parametre et au moment de redemarré j'ai le droit a un jolis kernel panic.
J'utilise un kernel déja compilé pour cette machine en .deb si quelqu'un pouvait me filé un petit coup de main sur ce probleme

Citation :

First stage kernel (Linux): Decompressing -- done

command line: 'console=ttyS0,115200 debug mem=22M cobalt_boot_image=/boot/vmlinux.bz2,/vmlinux.bz2,/boot/vmlinux.gz,/vmlinux.gz cobalt_boot_return=0x161f2b4 cobalt_boot_data=0x1634da0 cobalt_boot_load=0x1700000 cobalt_ramcode_map=0x1600000,0xa00000 ip=off '

booting kernel...

Linux version 2.4.16C14_ROM (root@cobalt) (gcc version egcs-2.91.66 19990314/Linux (egcs-1.1.2 release)) #1 Mon Jul 7 12:58:19 PDT 2003

BIOS-provided physical RAM map:

BIOS-e801: 0000000000000000 - 000000000009f000 (usable)

BIOS-e801: 0000000000100000 - 0000000020000000 (usable)

On node 0 totalpages: 5632

zone(0): 4096 pages.

zone(1): 1536 pages.

zone(2): 0 pages.

Kernel command line: console=ttyS0,115200 debug mem=22M cobalt_boot_image=/boot/vmlinux.bz2,/vmlinux.bz2,/boot/vmlinux.gz,/vmlinux.gz cobalt_boot_return=0x161f2b4 cobalt_boot_data=0x1634da0 cobalt_boot_load=0x1700000 cobalt_ramcode_map=0x1600000,0xa00000 ip=off

Initializing CPU#0

Detected 1263.113 MHz processor.

Calibrating delay loop... 2523.13 BogoMIPS

Memory: 19700k/22528k available (1487k kernel code, 2440k reserved, 258k data, 112k init, 0k highmem)

Dentry-cache hash table entries: 4096 (order: 3, 32768 bytes)

Inode-cache hash table entries: 2048 (order: 2, 16384 bytes)

Mount-cache hash table entries: 512 (order: 0, 4096 bytes)

Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)

Page-cache hash table entries: 8192 (order: 3, 32768 bytes)

CPU: Before vendor init, caps: 0383fbff 00000000 00000000, vendor = 0

CPU: L1 I cache: 16K, L1 D cache: 16K

CPU: L2 cache: 512K

Intel machine check architecture supported.

Intel machine check reporting enabled on CPU#0.

CPU: After vendor init, caps: 0383fbff 00000000 00000000 00000000

CPU: After generic, caps: 0383fbff 00000000 00000000 00000000

CPU: Common caps: 0383fbff 00000000 00000000 00000000

CPU: Intel(R) Pentium(R) III CPU - S 1266MHz stepping 04

Enabling fast FPU save and restore... done.

Enabling unmasked SIMD FPU exception support... done.

Checking 'hlt' instruction... OK.

POSIX conformance testing by UNIFIX

mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)

mtrr: detected mtrr type: Intel

PCI: Using configuration type 1

PCI: Probing PCI hardware

PCI: Discovered primary peer bus 01 [IRQ]

PCI: Using IRQ router ServerWorks [1166/0201] at 00:0f.0

PCI: Found IRQ 9 for device 00:0f.3

PCI: Sharing IRQ 9 with 00:0f.2

Linux NET4.0 for Linux 2.4

Based upon Swansea University Computer Society NET3.039

Initializing RT netlink socket

Starting kswapd

VFS: Diskquotas version dquot_6.4.0 initialized

SGI XFS with EAs, realtime, quota, no debug enabled

i2c-core.o: i2c core module

i2c-dev.o: i2c /dev entries driver module

i2c-core.o: driver i2c-dev dummy driver registered.

i2c-ali15x3.o version 2.6.2 (20011118)

i2c-ali15x3.o: Error: Can't detect ali15x3!

i2c-ali15x3.o: ALI15X3 not detected, module not inserted.

i2c-piix4.o version 2.6.2 (20011118)

i2c-piix4.o: Found CSB5 device

i2c-dev.o: Registered 'SMBus PIIX4 adapter at 3a80' as minor 0

i2c-core.o: adapter SMBus PIIX4 adapter at 3a80 registered as adapter 0.

i2c-piix4.o: SMBus detected and initialized

pty: 256 Unix98 ptys configured

Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled

ttyS00 at 0x03f8 (irq = 4) is a 16550A

ttyS01 at 0x02f8 (irq = 3) is a 16550A

Real Time Clock Driver v1.10e

Non-volatile memory driver v1.2

block: 64 slots per queue, batch=16

Uniform Multi-Platform E-IDE driver Revision: 6.31

ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx

ServerWorks CSB5: IDE controller on PCI bus 00 dev 79

ServerWorks CSB5: chipset revision 146

ServerWorks CSB5: native mode: will probe irqs later

ide0: BM-DMA at 0xfcb0-0xfcb7, BIOS settings: hda:DMA, hdb:DMA

ide1: BM-DMA at 0xfcb8-0xfcbf, BIOS settings: hdc:DMA, hdd:DMA

hda: ST380011A, SN=3JV4Z1LZ, FWREV=3.04, ATA DISK drive

ide0 at 0xfcd8-0xfcdf,0xfcd6 on irq 14

hda: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=155061/16/63, UDMA(100)

Partition check:

hda: hda1 hda2 hda3 hda4

natsemi.c:v1.07 1/9/2001 Written by Donald Becker <becker@scyld.com>

http://www.scyld.com/network/natsemi.html

(unofficial 2.4.x kernel port, version 1.07+LK1.0.15, Jan 14, 2002 Jeff Garzik, Tjeerd Mulder)

PCI: Found IRQ 5 for device 01:06.0

eth0: NatSemi DP8381[56] at 0xc2000000, 00:10:e0:06:3d:2e, IRQ 5.

PCI: Found IRQ 7 for device 01:07.0

eth1: NatSemi DP8381[56] at 0xc2002000, 00:10:e0:06:3c:64, IRQ 7.

SCSI subsystem driver Revision: 1.00

md: linear personality registered as nr 1

md: raid0 personality registered as nr 2

md: raid1 personality registered as nr 3

md: raid5 personality registered as nr 4

raid5: measuring checksumming speed

8regs : 1784.000 MB/sec

32regs : 1151.600 MB/sec

pIII_sse : 2961.600 MB/sec

pII_mmx : 2817.600 MB/sec

p5_mmx : 2988.000 MB/sec

raid5: using function: pIII_sse (2961.600 MB/sec)

md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27

md: Autodetecting RAID arrays.

md: autorun ...

md: ... autorun DONE.

NET4: Linux TCP/IP 1.0 for NET4.0

IP Protocols: ICMP, UDP, TCP

IP: routing cache hash table of 512 buckets, 4Kbytes

TCP: Hash tables configured (established 1024 bind 1024)

NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.

EXT2-fs: unable to read superblock

XFS: SB read failed

I/O error in filesystem ("md(9,1)" ) meta-data dev 0x901 block 0x0

("xfs_readsb" ) error 5 buf count 512

Kernel panic: VFS: Unable to mount root fs on 09:01

<6>disabling network interfaces.

Rebooting in 5 seconds..waiting for devices to flush..........done

Message édité par falcon56 le 19-07-2006 à 12:03:53

Publicité

francoispgp

ton erreur vient du filesysteme apparement tu es sur de l'avoir formaté aprés le partitionnement ? :lol: plus serieusement as tu bien fait ton fstab ? as tu bien formaté en XFS et pas autre chose ?

parceque tu utilises la bonne methode donc je penche plustot pour une petite bourde d'innattention de ce style au vu des messages d'erreurs

EXT2-fs: unable to read superblock

XFS: SB read failed

I/O error in filesystem ("md(9,1)" ) meta-data dev 0x901 block 0x0

("xfs_readsb" ) error 5 buf count 512

Kernel panic: VFS: Unable to mount root fs on 09:01

est ce que tu utilises un mode raid ? si voui il est pas démarré apparement.

Message édité par francoispgp le 19-07-2006 à 12:18:40

falcon56

bonne question !
normalement je doit formaté en ext2
et avoir / et /boot sur hda1 pour que le cobalt boot dessus
je n'ai jamais utilisé fdisk en ligne de commande ni les outils de formatage ( escuses....windows et install linux en graphique...)

voici mon fstab

Citation :

# /etc/fstab: static file system information.
#
# <file system> <mount point> <type> <options> <dump> <pass>
/dev/hda1 / ext2 default,errors=remount-ro 0 1
/dev/hda2 none swap sw 0 0
/dev/hda3 /var ext2 default 0 2
/dev/hda4 /opt ext2 default 0 0
proc /proc proc defaults 0 0

mais c'est comme tu dit surement une connerie de newbies

M300A

fdisk -l /dev/hda

Ton disk est pas bien partitionné je suppose

falcon56

voila mes partoches

Citation :

debian-nfs:~# fdisk -l /dev/hda

Disk /dev/hda: 16 heads, 63 sectors, 155061 cylinders
Units = cylinders of 1008 * 512 bytes

Device Boot Start End Blocks Id System
/dev/hda1 * 1 15876 8001472+ 83 Linux
/dev/hda2 15877 19846 2000880 82 Linux swap
/dev/hda3 19847 35682 7981344 83 Linux
/dev/hda4 35683 155061 60167016 83 Linux
debian-nfs:~#

c'est un 80 Go maintenant je sais que ce rack à une fonction raid mais je ne serait dire si le raid est Hardware ou software.
s'il est hardware normalement il est deja activé dans le kernel vus qu'en theorie ce kernel est fait pour cette bestiole.
en pratique c'est possible qu'il faut que je le parametre meme si je n'ai que 1 seul disk.

c'est forcement une connerie que j'oublie vus que la methode du deboostrap je l'ai faite pour le lecteur NFS mise a part l'install du kernel et des ln -sf a faire je ne vois pas trop ou je pourrais me planté, mise a part sur les partitions, le formatages et le fstab

falcon56

falcon56

M300A

Quel Filesystem sur hda1 ?

Humm il semble que ton cobalt cherche a booter sur un raid, je cherche une doc la dessus

M300A

Tu es deja rentré dans le bios de la bete ?

Cobalt:Main Menu> boot

Cobalt:Boot Menu> read_boot_type
From disk

Cobalt:Boot Menu> read_boot_dev
md1

Si le tiens renvoie ca il cherche a booter sur un volume md et non pas un hdd normal... Il faut que tu arrive a changer ce md1 en hda1

falcon56

ok j'ai reussis a passé en read_boot_dev hda1

j'ai toujours ce mesage d'erreur

c'est possible que ce soit une histoire de raid, le miens na qu'un seul disk dur de 80go

Publicité

falcon56

je refait une install complete depuis le debut

falcon56

Bon ça avance,
le cabalt à bien l'ai de vouloir booter sur le disk maintenant

j'ai de nouveau un kernel panic mais differant, j'ai utilisé le kernel précompilé de http://hugues.lepesant.com/

à voir s'il vaut mieux pas que j'installe le tient, je continus mes recherches

voila le log

Citation :

DIMM 0, none found
DIMM 1, RxCxB, Size/Index = DxBx4, 1x512MB/4, OK
DIMM 2, none found
DIMM 3, none found

Sun Cobalt - Smaller, Bluer, Better

Firmware version 2.9.38

Current date: Jul 27 14:46:57 UTC 2006

ROM build info: Mon Jul 7 13:00:58 PDT 2003 cobalt.sun.com

System serial number: S3490163

System type: 5000 series system, Version 2 board

Silicon serial number: 5333343930313633

Monitor: 153776 bytes

Memory: 512 MB

Initializing Local APIC ID 0 at 0xfee00000 (Virtual Wire mode)

SMP: relocate AP boot code from 0x01617200 to 0x0000a000 [size=65]

SMP: attempting to start CPU 3

Sending Start-Up IPI (Edge/Assert) to APIC 3 [vector 0x0a]

Sending Start-Up IPI (Edge/Assert) to APIC 3 [vector 0x0a]

Sending Start-Up IPI (Edge/Assert) to APIC 3 [vector 0x0a]

SMP: CPU 3 not found!

CPU: 1 processor(s) detected

CPU 0: GenuineIntel 1262MHz (9.5 x 133MHz host bus) [BSP]

Initializing flash: done

Flash Bank 0: AMD AM29F016B 2048KB (01:ad)

Flash Bank 1: not installed.

Mounting ROM fs: done

Initializing PCI: PIRQ: Relocate table to 0xf8000 (96 bytes, 4 entries, checksum b8)

OSB4 I/O port: 00:78 I/O base 0xfcfc [size=4]

OSB4 I/O port: 00:78 I/O base 0xfcf8 [size=4]

OSB4 I/O port: 00:78 I/O base 0xfcf4 [size=4]

OSB4 I/O port: 00:78 I/O base 0xfce8 [size=8]

OSB4 I/O port: 00:78 I/O base 0xfce0 [size=8]

done

Host Bus: 0 (device 00:00) [33MHz]

Device: 00:00 1166:0009 ServerWorks CNB30LE Host Bridge

Device: 00:01 1166:0009 ServerWorks CNB30LE Host Bridge

Device: 0f:00 1166:0201 ServerWorks CSB5 South Bridge (IRQ 10)

Device: 0f:01 1166:0212 ServerWorks CSB5 IDE Controller

Device: 0f:02 1166:0220 ServerWorks OpenHCI USB Controller (IRQ 9)

Device: 0f:03 1166:0230 ServerWorks CSB5 PCI-LPC Bridge

Host Bus: 1 (device 00:01) [33MHz]

Device: 06:00 100b:0020 National DP83815 MacPhyter Ethernet (IRQ 5)

Device: 07:00 100b:0020 National DP83815 MacPhyter Ethernet (IRQ 7)

MPTABLE: Bus #0 is PCI

MPTABLE: Bus #1 is PCI

MPTABLE: Bus #2 is ISA

MPTABLE: I/O Interrupt Entries

MPTABLE: TYPE POLARITY TRIGGER BUS IRQ APIC INT

MPTABLE: -------------------------------------------------------

MPTABLE: INT active-lo level PCI0 15:A 4 9

MPTABLE: INT active-lo level PCI1 6:A 5 0

MPTABLE: INT active-lo level PCI1 7:A 5 1

MPTABLE: EXT active-hi edge ISA 0 4 0

MPTABLE: INT active-hi edge ISA 0 4 0

MPTABLE: INT active-hi edge ISA 1 4 1

MPTABLE: INT active-hi edge ISA 3 4 3

MPTABLE: INT active-hi edge ISA 4 4 4

MPTABLE: INT active-hi edge ISA 8 4 8

MPTABLE: INT active-lo level ISA 10 4 10

MPTABLE: INT active-hi level ISA 14 4 14

MPTABLE: INT active-hi level ISA 15 4 15

MPTABLE: Local Interrupt Entries

MPTABLE: TYPE POLARITY TRIGGER BUS IRQ APIC INT

MPTABLE: -------------------------------------------------------

MPTABLE: EXT active-hi edge ISA 0 255 0

MPTABLE: NMI active-hi edge PCI0 0:A 255 1

SMP: floating table base 0x000f8200 (16 bytes, checksum ff)

SMP: config mptable base 0x000f8210 (216 bytes, checksum d5)

SMP: extended entry base 0x000f82e8 (144 bytes, checksum f3)

Initializing ethernet: 2 controller(s) found

National Semiconductor DP83815 Found at port 0xfe00, MAC: 00:10:e0:06:3d:2e

National Semiconductor DP83815 Found at port 0xfd00, MAC: 00:10:e0:06:3c:64

Initializing IDE: found ServerWorks CSB5 at 00:79

spinning up second channel: >>>>>done

scanning ide0: master

scanning ide1:

IDE: stabilizing spinup: 0% 1% 2% 3% 4% 5% 6% 7% 8% 9%10%11%12%13%14%15%16%17%18%19%20%21%22%23%24%25%26%27%28%29%30%31%32%33%34%35%36%37%38%39%40%41%42%43%44%45%46%47%48%49%50%51%52%53%54%55%56%57%58%59%60%61%62%63%64%65%66%67%68%69%70%71%72%73%74%75%76%77%78%79%80%81%82%83%84%85%86%87%88%89%90%91%92%93%94%95%96%97%98%99%100%

Checking Memory: done

Press spacebar to enter ROM mode

Booting default method - From disk

First stage kernel (Linux): Decompressing -- done

command line: 'console=ttyS0,115200 debug mem=22M cobalt_boot_image=/boot/vmlinux.bz2,/vmlinux.bz2,/boot/vmlinux.gz,/vmlinux.gz cobalt_boot_return=0x161f2b4 cobalt_boot_data=0x1634da0 cobalt_boot_load=0x1700000 cobalt_ramcode_map=0x1600000,0xa00000 ip=off '

booting kernel...

Linux version 2.4.16C14_ROM (root@cobalt) (gcc version egcs-2.91.66 19990314/Linux (egcs-1.1.2 release)) #1 Mon Jul 7 12:58:19 PDT 2003

BIOS-provided physical RAM map:

BIOS-e801: 0000000000000000 - 000000000009f000 (usable)

BIOS-e801: 0000000000100000 - 0000000020000000 (usable)

On node 0 totalpages: 5632

zone(0): 4096 pages.

zone(1): 1536 pages.

zone(2): 0 pages.

Kernel command line: console=ttyS0,115200 debug mem=22M cobalt_boot_image=/boot/vmlinux.bz2,/vmlinux.bz2,/boot/vmlinux.gz,/vmlinux.gz cobalt_boot_return=0x161f2b4 cobalt_boot_data=0x1634da0 cobalt_boot_load=0x1700000 cobalt_ramcode_map=0x1600000,0xa00000 ip=off

Initializing CPU#0

Detected 1263.113 MHz processor.

Calibrating delay loop... 2523.13 BogoMIPS

Memory: 19700k/22528k available (1487k kernel code, 2440k reserved, 258k data, 112k init, 0k highmem)

Dentry-cache hash table entries: 4096 (order: 3, 32768 bytes)

Inode-cache hash table entries: 2048 (order: 2, 16384 bytes)

Mount-cache hash table entries: 512 (order: 0, 4096 bytes)

Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)

Page-cache hash table entries: 8192 (order: 3, 32768 bytes)

CPU: Before vendor init, caps: 0383fbff 00000000 00000000, vendor = 0

CPU: L1 I cache: 16K, L1 D cache: 16K

CPU: L2 cache: 512K

Intel machine check architecture supported.

Intel machine check reporting enabled on CPU#0.

CPU: After vendor init, caps: 0383fbff 00000000 00000000 00000000

CPU: After generic, caps: 0383fbff 00000000 00000000 00000000

CPU: Common caps: 0383fbff 00000000 00000000 00000000

CPU: Intel(R) Pentium(R) III CPU - S 1266MHz stepping 04

Enabling fast FPU save and restore... done.

Enabling unmasked SIMD FPU exception support... done.

Checking 'hlt' instruction... OK.

POSIX conformance testing by UNIFIX

mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)

mtrr: detected mtrr type: Intel

PCI: Using configuration type 1

PCI: Probing PCI hardware

PCI: Discovered primary peer bus 01 [IRQ]

PCI: Using IRQ router ServerWorks [1166/0201] at 00:0f.0

PCI: Found IRQ 9 for device 00:0f.3

PCI: Sharing IRQ 9 with 00:0f.2

Linux NET4.0 for Linux 2.4

Based upon Swansea University Computer Society NET3.039

Initializing RT netlink socket

Starting kswapd

VFS: Diskquotas version dquot_6.4.0 initialized

SGI XFS with EAs, realtime, quota, no debug enabled

i2c-core.o: i2c core module

i2c-dev.o: i2c /dev entries driver module

i2c-core.o: driver i2c-dev dummy driver registered.

i2c-ali15x3.o version 2.6.2 (20011118)

i2c-ali15x3.o: Error: Can't detect ali15x3!

i2c-ali15x3.o: ALI15X3 not detected, module not inserted.

i2c-piix4.o version 2.6.2 (20011118)

i2c-piix4.o: Found CSB5 device

i2c-dev.o: Registered 'SMBus PIIX4 adapter at 3a80' as minor 0

i2c-core.o: adapter SMBus PIIX4 adapter at 3a80 registered as adapter 0.

i2c-piix4.o: SMBus detected and initialized

pty: 256 Unix98 ptys configured

Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled

ttyS00 at 0x03f8 (irq = 4) is a 16550A

ttyS01 at 0x02f8 (irq = 3) is a 16550A

Real Time Clock Driver v1.10e

Non-volatile memory driver v1.2

block: 64 slots per queue, batch=16

Uniform Multi-Platform E-IDE driver Revision: 6.31

ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx

ServerWorks CSB5: IDE controller on PCI bus 00 dev 79

ServerWorks CSB5: chipset revision 146

ServerWorks CSB5: native mode: will probe irqs later

ide0: BM-DMA at 0xfcb0-0xfcb7, BIOS settings: hda:DMA, hdb:DMA

ide1: BM-DMA at 0xfcb8-0xfcbf, BIOS settings: hdc:DMA, hdd:DMA

hda: ST380011A, SN=3JV4Z1LZ, FWREV=3.04, ATA DISK drive

ide0 at 0xfcd8-0xfcdf,0xfcd6 on irq 14

hda: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=155061/16/63, UDMA(100)

Partition check:

hda: hda1 hda2 hda3 hda4

natsemi.c:v1.07 1/9/2001 Written by Donald Becker <becker@scyld.com>

http://www.scyld.com/network/natsemi.html

(unofficial 2.4.x kernel port, version 1.07+LK1.0.15, Jan 14, 2002 Jeff Garzik, Tjeerd Mulder)

PCI: Found IRQ 5 for device 01:06.0

eth0: NatSemi DP8381[56] at 0xc2000000, 00:10:e0:06:3d:2e, IRQ 5.

PCI: Found IRQ 7 for device 01:07.0

eth1: NatSemi DP8381[56] at 0xc2002000, 00:10:e0:06:3c:64, IRQ 7.

SCSI subsystem driver Revision: 1.00

md: linear personality registered as nr 1

md: raid0 personality registered as nr 2

md: raid1 personality registered as nr 3

md: raid5 personality registered as nr 4

raid5: measuring checksumming speed

8regs : 1784.800 MB/sec

32regs : 1151.600 MB/sec

pIII_sse : 2961.600 MB/sec

pII_mmx : 2817.600 MB/sec

p5_mmx : 2988.000 MB/sec

raid5: using function: pIII_sse (2961.600 MB/sec)

md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27

md: Autodetecting RAID arrays.

md: autorun ...

md: ... autorun DONE.

NET4: Linux TCP/IP 1.0 for NET4.0

IP Protocols: ICMP, UDP, TCP

IP: routing cache hash table of 512 buckets, 4Kbytes

TCP: Hash tables configured (established 1024 bind 1024)

NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.

VFS: Mounted root (ext2 filesystem) readonly.

Freeing unused kernel memory: 112k freed

BOOTLOADER: Mapping in physical locations

BOOTLOADER: load_addr=0xc2004000 ret_data=0xc2205da0

BOOTLOADER: opening "/boot/vmlinux.bz2"

BOOTLOADER: opening "/vmlinux.bz2"

BOOTLOADER: opening "/boot/vmlinux.gz"

BOOTLOADER: reading "/boot/vmlinux.gz"

BOOTLOADER: read 808803bytes

BOOTLOADER: unmounting /

BOOTLOADER: calling reboot notifiers

md: stopping all md devices.

flushing ide devices: hda

disabling network interfaces.

BOOTLOADER: mapping 22M-32M for ride home

BOOTLOADER: disabling interupts

BOOTLOADER: flushing cache

BOOTLOADER: Leap of faith!

Back in ramcode: done

Second stage kernel: Decompressing -Error bunzip2ing kernel. Trying gunzip.

\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-- done

command line: 'console=ttyS0,115200 debug ip=off '

booting kernel...

Linux version 2.4.32 (root@persephone.tite-cabane.org) (gcc version 2.95.4 20011002 (Debian prerelease)) #1 Wed Jan 4 12:44:21 CET 2006

BIOS-provided physical RAM map:

BIOS-e801: 0000000000000000 - 000000000009f000 (usable)

BIOS-e801: 0000000000100000 - 0000000020000000 (usable)

512MB LOWMEM available.

On node 0 totalpages: 131072

zone(0): 4096 pages.

zone(1): 126976 pages.

zone(2): 0 pages.

DMI not present.

Kernel command line: console=ttyS0,115200 debug ip=off

Initializing CPU#0

Detected 1263.113 MHz processor.

Calibrating delay loop... 2523.13 BogoMIPS

Memory: 516656k/524288k available (1018k kernel code, 7244k reserved, 290k data, 80k init, 0k highmem)

Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)

Inode cache hash table entries: 32768 (order: 6, 262144 bytes)

Mount cache hash table entries: 512 (order: 0, 4096 bytes)

Buffer cache hash table entries: 32768 (order: 5, 131072 bytes)

Page-cache hash table entries: 131072 (order: 7, 524288 bytes)

CPU: L1 I cache: 16K, L1 D cache: 16K

CPU: L2 cache: 512K

CPU: After generic, caps: 0383fbff 00000000 00000000 00000000

CPU: Common caps: 0383fbff 00000000 00000000 00000000

CPU: Intel(R) Pentium(R) III CPU - S 1266MHz stepping 04

Enabling fast FPU save and restore... done.

Enabling unmasked SIMD FPU exception support... done.

Checking 'hlt' instruction... OK.

POSIX conformance testing by UNIFIX

mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)

mtrr: detected mtrr type: Intel

PCI: Using configuration type 1

PCI: Probing PCI hardware

PCI: Probing PCI hardware (bus 00)

PCI: Ignoring BAR0-3 of IDE controller 00:0f.1

PCI: Discovered primary peer bus 01 [IRQ]

PCI: Using IRQ router ServerWorks [1166/0201] at 00:0f.0

PCI: Found IRQ 9 for device 00:0f.3

PCI: Sharing IRQ 9 with 00:0f.2

Cobalt system type is unknown (trouble will ensue)

Unable to handle kernel NULL pointer dereference at virtual address 0000000c

printing eip:

c01b5e19

*pde = 00000000

Oops: 0000

CPU: 0

EIP: 0010:[<c01b5e19>] Not tainted

EFLAGS: 00010293

eax: 00000000 ebx: 00010f00 ecx: 00000001 edx: 00000001

esi: c0249fc0 edi: 00000000 ebp: 01ffffec esp: c159dfdc

ds: 0018 es: 0018 ss: 0018

Process swapper (pid: 1, stackpage=c159d000)

Stack: c0257b4f c024a6a8 c010505b 00010f00 c0249fc0 c010566c 00000000 00000078

c0248000

Call Trace: [<c010505b>] [<c010566c>]

Code: 8b 50 0c 81 e2 f0 ff 00 00 89 50 0c 75 17 68 76 13 22 c0 68

<0>Kernel panic: Attempted to kill init!

Message édité par falcon56 le 27-07-2006 à 16:55:14

M300A

Très étrange.
Utilise plutot le mien.

falcon56

le bout du tunel arrive ;) enfin normalement ^^
plein de petite erreurs je pense mais plus de kernel panic
le cobalt a l'air de booter plusieur foix le kernel ( en dehors du "bios" )

Citation :

DIMM 0, none found
DIMM 1, RxCxB, Size/Index = DxBx4, 1x512MB/4, OK
DIMM 2, none found
DIMM 3, none found

Sun Cobalt - Smaller, Bluer, Better

Firmware version 2.9.38

Current date: Jul 27 15:44:54 UTC 2006

ROM build info: Mon Jul 7 13:00:58 PDT 2003 cobalt.sun.com

System serial number: S3490163

System type: 5000 series system, Version 2 board

Silicon serial number: 5333343930313633

Monitor: 153776 bytes

Memory: 512 MB

Initializing Local APIC ID 0 at 0xfee00000 (Virtual Wire mode)

SMP: relocate AP boot code from 0x01617200 to 0x0000a000 [size=65]

SMP: attempting to start CPU 3

Sending Start-Up IPI (Edge/Assert) to APIC 3 [vector 0x0a]

Sending Start-Up IPI (Edge/Assert) to APIC 3 [vector 0x0a]

Sending Start-Up IPI (Edge/Assert) to APIC 3 [vector 0x0a]

SMP: CPU 3 not found!

CPU: 1 processor(s) detected

CPU 0: GenuineIntel 1263MHz (9.5 x 133MHz host bus) [BSP]

Initializing flash: done

Flash Bank 0: AMD AM29F016B 2048KB (01:ad)

Flash Bank 1: not installed.

Mounting ROM fs: done

Initializing PCI: PIRQ: Relocate table to 0xf8000 (96 bytes, 4 entries, checksum b8)

OSB4 I/O port: 00:78 I/O base 0xfcfc [size=4]

OSB4 I/O port: 00:78 I/O base 0xfcf8 [size=4]

OSB4 I/O port: 00:78 I/O base 0xfcf4 [size=4]

OSB4 I/O port: 00:78 I/O base 0xfce8 [size=8]

OSB4 I/O port: 00:78 I/O base 0xfce0 [size=8]

done

Host Bus: 0 (device 00:00) [33MHz]

Device: 00:00 1166:0009 ServerWorks CNB30LE Host Bridge

Device: 00:01 1166:0009 ServerWorks CNB30LE Host Bridge

Device: 0f:00 1166:0201 ServerWorks CSB5 South Bridge (IRQ 10)

Device: 0f:01 1166:0212 ServerWorks CSB5 IDE Controller

Device: 0f:02 1166:0220 ServerWorks OpenHCI USB Controller (IRQ 9)

Device: 0f:03 1166:0230 ServerWorks CSB5 PCI-LPC Bridge

Host Bus: 1 (device 00:01) [33MHz]

Device: 06:00 100b:0020 National DP83815 MacPhyter Ethernet (IRQ 5)

Device: 07:00 100b:0020 National DP83815 MacPhyter Ethernet (IRQ 7)

MPTABLE: Bus #0 is PCI

MPTABLE: Bus #1 is PCI

MPTABLE: Bus #2 is ISA

MPTABLE: I/O Interrupt Entries

MPTABLE: TYPE POLARITY TRIGGER BUS IRQ APIC INT

MPTABLE: -------------------------------------------------------

MPTABLE: INT active-lo level PCI0 15:A 4 9

MPTABLE: INT active-lo level PCI1 6:A 5 0

MPTABLE: INT active-lo level PCI1 7:A 5 1

MPTABLE: EXT active-hi edge ISA 0 4 0

MPTABLE: INT active-hi edge ISA 0 4 0

MPTABLE: INT active-hi edge ISA 1 4 1

MPTABLE: INT active-hi edge ISA 3 4 3

MPTABLE: INT active-hi edge ISA 4 4 4

MPTABLE: INT active-hi edge ISA 8 4 8

MPTABLE: INT active-lo level ISA 10 4 10

MPTABLE: INT active-hi level ISA 14 4 14

MPTABLE: INT active-hi level ISA 15 4 15

MPTABLE: Local Interrupt Entries

MPTABLE: TYPE POLARITY TRIGGER BUS IRQ APIC INT

MPTABLE: -------------------------------------------------------

MPTABLE: EXT active-hi edge ISA 0 255 0

MPTABLE: NMI active-hi edge PCI0 0:A 255 1

SMP: floating table base 0x000f8200 (16 bytes, checksum ff)

SMP: config mptable base 0x000f8210 (216 bytes, checksum d5)

SMP: extended entry base 0x000f82e8 (144 bytes, checksum f3)

Initializing ethernet: 2 controller(s) found

National Semiconductor DP83815 Found at port 0xfe00, MAC: 00:10:e0:06:3d:2e

National Semiconductor DP83815 Found at port 0xfd00, MAC: 00:10:e0:06:3c:64

Initializing IDE: found ServerWorks CSB5 at 00:79

spinning up second channel: >>>>>done

scanning ide0: master

scanning ide1:

IDE: stabilizing spinup:
0% 1% 2% 3% 4% 5% 6% 7% 8% 9%10%11%12%13%14%15%16%17%18%19%20%21%22%23%24%25%26%27%28%29%30%31%32%33%34%35%36%37%38%39%40%41%42%43%44%45%46%47%48%49%50%51%52%53%54%55%56%57%58%59%60%61%62%63%64%65%66%67%68%69%70%71%72%73%74%75%76%77%78%79%80%81%82%83%84%85%86%87%88%89%90%91%92%93%94%95%96%97%98%99%100%

Checking Memory: done

Press spacebar to enter ROM mode

Booting default method - From disk

First stage kernel (Linux): Decompressing -- done

command line: 'console=ttyS0,115200 debug mem=22M cobalt_boot_image=/boot/vmlinux.bz2,/vmlinux.bz2,/boot/vmlinux.gz,/vmlinux.gz cobalt_boot_return=0x161f2b4 cobalt_boot_data=0x1634da0 cobalt_boot_load=0x1700000 cobalt_ramcode_map=0x1600000,0xa00000 ip=off '

booting kernel...

Linux version 2.4.16C14_ROM (root@cobalt) (gcc version egcs-2.91.66 19990314/Linux (egcs-1.1.2 release)) #1 Mon Jul 7 12:58:19 PDT 2003

BIOS-provided physical RAM map:

BIOS-e801: 0000000000000000 - 000000000009f000 (usable)

BIOS-e801: 0000000000100000 - 0000000020000000 (usable)

On node 0 totalpages: 5632

zone(0): 4096 pages.

zone(1): 1536 pages.

zone(2): 0 pages.

Kernel command line: console=ttyS0,115200 debug mem=22M cobalt_boot_image=/boot/vmlinux.bz2,/vmlinux.bz2,/boot/vmlinux.gz,/vmlinux.gz cobalt_boot_return=0x161f2b4 cobalt_boot_data=0x1634da0 cobalt_boot_load=0x1700000 cobalt_ramcode_map=0x1600000,0xa00000 ip=off

Initializing CPU#0

Detected 1263.113 MHz processor.

Calibrating delay loop... 2516.58 BogoMIPS

Memory: 19700k/22528k available (1487k kernel code, 2440k reserved, 258k data, 112k init, 0k highmem)

Dentry-cache hash table entries: 4096 (order: 3, 32768 bytes)

Inode-cache hash table entries: 2048 (order: 2, 16384 bytes)

Mount-cache hash table entries: 512 (order: 0, 4096 bytes)

Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)

Page-cache hash table entries: 8192 (order: 3, 32768 bytes)

CPU: Before vendor init, caps: 0383fbff 00000000 00000000, vendor = 0

CPU: L1 I cache: 16K, L1 D cache: 16K

CPU: L2 cache: 512K

Intel machine check architecture supported.

Intel machine check reporting enabled on CPU#0.

CPU: After vendor init, caps: 0383fbff 00000000 00000000 00000000

CPU: After generic, caps: 0383fbff 00000000 00000000 00000000

CPU: Common caps: 0383fbff 00000000 00000000 00000000

CPU: Intel(R) Pentium(R) III CPU - S 1266MHz stepping 04

Enabling fast FPU save and restore... done.

Enabling unmasked SIMD FPU exception support... done.

Checking 'hlt' instruction... OK.

POSIX conformance testing by UNIFIX

mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)

mtrr: detected mtrr type: Intel

PCI: Using configuration type 1

PCI: Probing PCI hardware

PCI: Discovered primary peer bus 01 [IRQ]

PCI: Using IRQ router ServerWorks [1166/0201] at 00:0f.0

PCI: Found IRQ 9 for device 00:0f.3

PCI: Sharing IRQ 9 with 00:0f.2

Linux NET4.0 for Linux 2.4

Based upon Swansea University Computer Society NET3.039

Initializing RT netlink socket

Starting kswapd

VFS: Diskquotas version dquot_6.4.0 initialized

SGI XFS with EAs, realtime, quota, no debug enabled

i2c-core.o: i2c core module

i2c-dev.o: i2c /dev entries driver module

i2c-core.o: driver i2c-dev dummy driver registered.

i2c-ali15x3.o version 2.6.2 (20011118)

i2c-ali15x3.o: Error: Can't detect ali15x3!

i2c-ali15x3.o: ALI15X3 not detected, module not inserted.

i2c-piix4.o version 2.6.2 (20011118)

i2c-piix4.o: Found CSB5 device

i2c-dev.o: Registered 'SMBus PIIX4 adapter at 3a80' as minor 0

i2c-core.o: adapter SMBus PIIX4 adapter at 3a80 registered as adapter 0.

i2c-piix4.o: SMBus detected and initialized

pty: 256 Unix98 ptys configured

Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled

ttyS00 at 0x03f8 (irq = 4) is a 16550A

ttyS01 at 0x02f8 (irq = 3) is a 16550A

Real Time Clock Driver v1.10e

Non-volatile memory driver v1.2

block: 64 slots per queue, batch=16

Uniform Multi-Platform E-IDE driver Revision: 6.31

ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx

ServerWorks CSB5: IDE controller on PCI bus 00 dev 79

ServerWorks CSB5: chipset revision 146

ServerWorks CSB5: native mode: will probe irqs later

ide0: BM-DMA at 0xfcb0-0xfcb7, BIOS settings: hda:DMA, hdb:DMA

ide1: BM-DMA at 0xfcb8-0xfcbf, BIOS settings: hdc:DMA, hdd:DMA

hda: ST380011A, SN=3JV4Z1LZ, FWREV=3.04, ATA DISK drive

ide0 at 0xfcd8-0xfcdf,0xfcd6 on irq 14

hda: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=155061/16/63, UDMA(100)

Partition check:

hda: hda1 hda2 hda3 hda4

natsemi.c:v1.07 1/9/2001 Written by Donald Becker <becker@scyld.com>

http://www.scyld.com/network/natsemi.html

(unofficial 2.4.x kernel port, version 1.07+LK1.0.15, Jan 14, 2002 Jeff Garzik, Tjeerd Mulder)

PCI: Found IRQ 5 for device 01:06.0

eth0: NatSemi DP8381[56] at 0xc2000000, 00:10:e0:06:3d:2e, IRQ 5.

PCI: Found IRQ 7 for device 01:07.0

eth1: NatSemi DP8381[56] at 0xc2002000, 00:10:e0:06:3c:64, IRQ 7.

SCSI subsystem driver Revision: 1.00

md: linear personality registered as nr 1

md: raid0 personality registered as nr 2

md: raid1 personality registered as nr 3

md: raid5 personality registered as nr 4

raid5: measuring checksumming speed

8regs : 1784.000 MB/sec

32regs : 1151.600 MB/sec

pIII_sse : 2961.600 MB/sec

pII_mmx : 2818.000 MB/sec

p5_mmx : 2988.000 MB/sec

raid5: using function: pIII_sse (2961.600 MB/sec)

md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27

md: Autodetecting RAID arrays.

md: autorun ...

md: ... autorun DONE.

NET4: Linux TCP/IP 1.0 for NET4.0

IP Protocols: ICMP, UDP, TCP

IP: routing cache hash table of 512 buckets, 4Kbytes

TCP: Hash tables configured (established 1024 bind 1024)

NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.

VFS: Mounted root (ext2 filesystem) readonly.

Freeing unused kernel memory: 112k freed

BOOTLOADER: Mapping in physical locations

BOOTLOADER: load_addr=0xc2004000 ret_data=0xc2205da0

BOOTLOADER: opening "/boot/vmlinux.bz2"

BOOTLOADER: opening "/vmlinux.bz2"

BOOTLOADER: opening "/boot/vmlinux.gz"

BOOTLOADER: reading "/boot/vmlinux.gz"

BOOTLOADER: read 1246032bytes

BOOTLOADER: unmounting /

BOOTLOADER: calling reboot notifiers

md: stopping all md devices.

flushing ide devices: hda

disabling network interfaces.

BOOTLOADER: mapping 22M-32M for ride home

BOOTLOADER: disabling interupts

BOOTLOADER: flushing cache

BOOTLOADER: Leap of faith!

Back in ramcode: done

Second stage kernel: Decompressing -Error bunzip2ing kernel. Trying gunzip.

\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/- done

ERROR: cannot relocate with filesize 0

command line: 'console=ttyS0,115200 debug ip=off '

booting kernel...

Linux version 2.4.32-raq550 (root@thrall) (gcc version 3.3.6 (Debian 1:3.3.6-13)) #1 Sun Jul 9 18:36:15 UTC 2006

BIOS-provided physical RAM map:

BIOS-e801: 0000000000000000 - 000000000009f000 (usable)

BIOS-e801: 0000000000100000 - 0000000020000000 (usable)

512MB LOWMEM available.

On node 0 totalpages: 131072

zone(0): 4096 pages.

zone(1): 126976 pages.

zone(2): 0 pages.

DMI not present.

Kernel command line: console=ttyS0,115200 debug ip=off

Initializing CPU#0

Detected 1263.113 MHz processor.

Calibrating delay loop... 2523.13 BogoMIPS

Memory: 515820k/524288k available (1796k kernel code, 8080k reserved, 328k data, 92k init, 0k highmem)

Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)

Inode cache hash table entries: 32768 (order: 6, 262144 bytes)

Mount cache hash table entries: 512 (order: 0, 4096 bytes)

Buffer cache hash table entries: 32768 (order: 5, 131072 bytes)

Page-cache hash table entries: 131072 (order: 7, 524288 bytes)

CPU: L1 I cache: 16K, L1 D cache: 16K

CPU: L2 cache: 512K

CPU: After generic, caps: 0383fbff 00000000 00000000 00000000

CPU: Common caps: 0383fbff 00000000 00000000 00000000

CPU: Intel(R) Pentium(R) III CPU - S 1266MHz stepping 04

Enabling fast FPU save and restore... done.

Enabling unmasked SIMD FPU exception support... done.

Checking 'hlt' instruction... OK.

POSIX conformance testing by UNIFIX

PCI: Using configuration type 1

PCI: Probing PCI hardware

PCI: Probing PCI hardware (bus 00)

PCI: Ignoring BAR0-3 of IDE controller 00:0f.1

PCI: Discovered primary peer bus 01 [IRQ]

PCI: Using IRQ router ServerWorks [1166/0201] at 00:0f.0

PCI: Found IRQ 9 for device 00:0f.3

PCI: Sharing IRQ 9 with 00:0f.2

Linux NET4.0 for Linux 2.4

Based upon Swansea University Computer Society NET3.039

Initializing RT netlink socket

Starting kswapd

VFS: Disk quotas vdquot_6.5.1

Journalled Block Device driver loaded

Installing knfsd (copyright (C) 1996 okir@monad.swb.de).

SGI XFS with no debug enabled

Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled

ttyS00 at 0x03f8 (irq = 4) is a 16550A

ttyS01 at 0x02f8 (irq = 3) is a 16550A

Real Time Clock Driver v1.10f

Non-volatile memory driver v1.2

loop: loaded (max 8 devices)

natsemi dp8381x driver, version 1.07+LK1.0.17, Sep 27, 2002

originally by Donald Becker <becker@scyld.com>

http://www.scyld.com/network/natsemi.html

2.4.x kernel port by Jeff Garzik, Tjeerd Mulder

PCI: Found IRQ 5 for device 01:06.0

eth0: NatSemi DP8381[56] at 0xe0800000, 00:10:e0:06:3d:2e, IRQ 5.

PCI: Found IRQ 7 for device 01:07.0

eth1: NatSemi DP8381[56] at 0xe0802000, 00:10:e0:06:3c:64, IRQ 7.

Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4

ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx

SvrWks CSB5: IDE controller at PCI slot 00:0f.1

SvrWks CSB5: chipset revision 146

SvrWks CSB5: not 100% native mode: will probe irqs later

ide0: BM-DMA at 0xfcb0-0xfcb7, BIOS settings: hda:DMA, hdb:DMA

ide1: BM-DMA at 0xfcb8-0xfcbf, BIOS settings: hdc:DMA, hdd:DMA

hda: ST380011A, ATA DISK drive

blk: queue c034dba0, I/O limit 4095Mb (mask 0xffffffff)

ide0 at 0x1f0-0x1f7,0x3f6 on irq 14

hda: attached ide-disk driver.

hda: host protected area => 1

hda: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=9729/255/63, UDMA(100)

Partition check:

hda: hda1 hda2 hda3 hda4

usb.c: registered new driver usbdevfs

usb.c: registered new driver hub

PCI: Found IRQ 9 for device 00:0f.2

PCI: Sharing IRQ 9 with 00:0f.3

host/usb-ohci.c: USB OHCI at membase 0xe0804000, IRQ 9

host/usb-ohci.c: usb-00:0f.2, PCI device 1166:0220

usb.c: new USB bus registered, assigned bus number 1

hub.c: USB hub found

hub.c: 2 ports detected

md: linear personality registered as nr 1

md: raid0 personality registered as nr 2

md: raid1 personality registered as nr 3

md: raid5 personality registered as nr 4

raid5: measuring checksumming speed

8regs : 2328.000 MB/sec

32regs : 1195.600 MB/sec

pIII_sse : 2988.000 MB/sec

pII_mmx : 2843.200 MB/sec

p5_mmx : 2958.000 MB/sec

raid5: using function: pIII_sse (2988.000 MB/sec)

md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27

md: Autodetecting RAID arrays.

md: autorun ...

md: ... autorun DONE.

LVM version 1.0.8(17/11/2003)

NET4: Linux TCP/IP 1.0 for NET4.0

IP Protocols: ICMP, UDP, TCP

IP: routing cache hash table of 4096 buckets, 32Kbytes

TCP: Hash tables configured (established 131072 bind 65536)

NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.

802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>

All bugs added by David S. Miller <davem@redhat.com>

VFS: Mounted root (ext2 filesystem) readonly.

Freeing unused kernel memory: 92k freed

INIT: version 2.86 booting mount: wrong fs type, bad option, bad superblock on tmpfs,
missing codepage or other error
In some cases useful info is found in syslog - try
dmesg | tail or so

Adding Swap: 2000872k swap-space (priority -1)

Checking root file system...
fsck 1.37 (21-Mar-2005)
/dev/hda1: clean, 21323/1001920 EXT2-fs: Unrecognized mount option default

files, 74211/2000368 blocks
EXT2-fs: Unrecognized mount option default

mount: / not mounted already, or bad option
Cleaning up ifupdown...done.
Not calculating module dependencies: /lib/modules/2.4.32-raq550 is read only.
Loading modules:
Checking all file systems...
fsck 1.37 (21-Mar-2005)
/dev/hda3: clean, 918/999424 files, 57951/1995336 blocks
... done.
EXT2-fs: Unrecognized mount option default

EXT2-fs: Unrecognized mount option default

mount: wrong fs type, bad option, bad superblock on /dev/hda3,
missing codepage or other error
In some cases useful info is found in syslog - try
dmesg | tail or so

mount: wrong fs type, bad option, bad superblock on /dev/hda4,
missing codepage or other error
In some cases useful info is found in syslog - try
dmesg | tail or so

/etc/init.d/rcS: line 39: /tmp/.clean: Read-only file system
mount: wrong fs type, bad option, bad superblock on tmpfs,
missing codepage or other error
In some cases useful info is found in syslog - try
dmesg | tail or so

Running 0dns-down to make sure resolv.conf is ok.../etc/ppp/ip-down.d/0dns-down: line 33: cd: /var/run/pppconfig: No such file or directory
Setting up networking.../etc/rcS.d/S39ifupdown: line 75: /etc/network/run/ifstate: Read-only file system
failed.
S39ifupdown: Error: Failure initializing /etc/network/run/ifstate
Setting up IP spoofing protection: rp_filter.
Configuring network interfaces...ifup: failed to open statefile /etc/network/run/ifstate: Read-only file system
done.
/etc/init.d/rcS: line 39: /tmp/.clean: Read-only file system
/etc/init.d/rcS: line 24: /var/run/utmp: No such file or directory
urandom start: failed.

INIT: Entering runlevel: 2 Starting system log daemon: syslogdchmod: changing permissions of `/dev/xconsole': Read-only file system

Message édité par falcon56 le 27-07-2006 à 17:52:28

M300A

C'est marqué default dans le fstab ca existe pas

C'est defaults

falcon56

sic pour ma defence le correcteur de n'ortograffe n'avais rien vus !

j'ai bien le prompt ! ça y est presque une derniere chose est ce que tu a reussis à récupéré l'affichage LCD ?
est ce que l'on peut régulé la ventilation aussi ?

M300A

regulé la ventil je pense pas. J'ai eclaté mon cobalt avec des 92mm perso.

L'afficheur LCD oui on peut, j'avais commencer a bosser sur le paquet debian du truc, mais pff pas eu le temps (melisaaaaaaaaaaaaaaaaaaaaa )

J'essyerais de te trouver mes debs, ils sont pas finit mais ca marche

falcon56

héhé cool merci
bon bas mon server apache, php, mysql, phpmyadmin fonctionne !

me reste encore ssh ça ma pas l'air de marché, crée un serveur ftp pour les upploads de fichiers, et puis avoir une interface d'aministration globale

encore pas mal de boulot en perspective !

en tout cas je te remerci de ton aide et de ta patience

FORUM HardWare.fr

Linux et OS Alternatifs

Installation

Besoin d'aide sur un kernel panic

Sujets relatifs
[debian] Sources du kernel 2.6.17-1-k7	Utilisation de Gtranscode, une petite aide ?
kernel land	besoin d'un OS gratuit pour un don informatique à une école
besoin non logiceil aide moi svp ?	aide pour la remise en route d'un 300mhz
re-linuxien besoin daide (ati+sata ^^)	besoin d'aide pour reseau WIFI + freebox + Xbox + Xbox360
Plus de sujets relatifs à : Besoin d'aide sur un kernel panic

Page générée en 0.073 secondes