Bonjour.
 
J'ai un problème avec lilo: ce dernier ne veut plus s'installer! quand je tappe lilo, il me réponds "Fatal: stat /dev/hda1bios: No such file or directory"
 
D'où ça vient? svp c'est très génant parceque là j'ai un Pc qui boote carément plus  

dans lilo.conf, yas pas une ligne ou un espace aurait pu être supprimé (ou un retour à la ligne) et donc tu aurais /dev/hda1bios ?

# /etc/lilo.conf - See: `lilo(8)' and `lilo.conf(5)',
# ---------------       `install-mbr(8)', `/usr/share/doc/lilo/',
#                       and `/usr/share/doc/mbr/'.
 
# +---------------------------------------------------------------+
# |                        !! Reminder !!                         |
# |                                                               |
# | Don't forget to run `lilo' after you make changes to this     |
# | conffile, `/boot/bootmess.txt', or install a new kernel.  The |
# | computer will most likely fail to boot if a kernel-image      |
# | post-install script or you don't remember to run `lilo'.      |
# |                                                               |
# +---------------------------------------------------------------+
 
# Support LBA for large hard disks.
#
lba32
 
# Overrides the default mapping between harddisk names and the BIOS'
# harddisk order. Use with caution.
disk=/dev/hda1bios=0x80
 
 
# Specifies the boot device.  This is where Lilo installs its boot
# block.  It can be either a partition, or the raw device, in which
# case it installs in the MBR, and will overwrite the current MBR.
#
boot=/dev/hda1
# Specifies the device that should be mounted as root. (`/')
#
root=/dev/hda5
 
# Enable map compaction:
# Tries to merge read requests for adjacent sectors into a single
# read request. This drastically reduces load time and keeps the
# map smaller.  Using `compact' is especially recommended when
# booting from a floppy disk.  It is disabled here by default
# because it doesn't always work.
#
# compact
 
# Installs the specified file as the new boot sector
# You have the choice between: bmp, compat, menu and text
# Look in /boot/ and in lilo.conf(5) manpage for details
#
install=/boot/boot-menu.b
 
# Specifies the location of the map file
#
map=/boot/map
 
# You can set a password here, and uncomment the `restricted' lines
# in the image definitions below to make it so that a password must
# be typed to boot anything but a default configuration.  If a
# command line is given, other than one specified by an `append'
# statement in `lilo.conf', the password will be required, but a
# standard default boot will not require one.
#
# This will, for instance, prevent anyone with access to the
# console from booting with something like `Linux init=/bin/sh',
# and thus becoming `root' without proper authorization.
#
# Note that if you really need this type of security, you will
# likely also want to use `install-mbr' to reconfigure the MBR
# program, as well as set up your BIOS to disallow booting from
# removable disk or CD-ROM, then put a password on getting into the
# BIOS configuration as well.  Please RTFM `install-mbr(8)'.
#
# password=tatercounter2000
 
# Specifies the number of deciseconds (0.1 seconds) LILO should
# wait before booting the first image.
#
delay=20
 
# You can put a customized boot message up if you like.  If you use
# `prompt', and this computer may need to reboot unattended, you
# must specify a `timeout', or it will sit there forever waiting
# for a keypress.  `single-key' goes with the `alias' lines in the
# `image' configurations below.  eg: You can press `1' to boot
# `Linux', `2' to boot `LinuxOLD', if you uncomment the `alias'.
#
# message=/boot/bootmess.txt
prompt
timeout=30
# prompt
# single-key
# delay=100
# timeout=100
 
# Specifies the VGA text mode at boot time. (normal, extended, ask, <mode> )
#
# vga=ask
# vga=9
#
vga=normal
 
# Kernel command line options that apply to all installed images go
# here.  See: The `boot-prompt-HOWO' and `kernel-parameters.txt' in
# the Linux kernel `Documentation' directory.
#
# append=""
 
# Boot up Linux by default.
#
default=Linux
 
# Kernel 2.4.21
image=/vmlinuz
 label=Linux
 read-only
# append="hdd=ide-scsi"
# restricted
# alias=1
 
 
# Kernel 2.4.20
image=/vmlinuz.old
 label=LinuxOLD
 read-only
 optional
# restricted
# alias=2
 
# If you have another OS on this machine to boot, you can uncomment the
# following lines, changing the device name on the `other' line to
# where your other OS' partition is.
#
# other=/dev/hda4
# label=HURD
# restricted
# alias=3
 
 
# Memtest
image=/boot/memtest86.bin
 label=Memtest86

alors j'ai commenté la ligne disk=/dev/hda1bios=0x80 et j'ai mis le boot en hda plutôt qu'en hda1 et ça marche, merci    

 
Mmmm

je comprends pas d'où ça vient ce truc!

un retour chariot qui a dégagé la dernière fois que tu as édité lilo.conf  

 
Oui ou un # qui s'est évadé, va savoir dans le monde du libre  

je pense que c'est un # qui s'est barré.
 
le truc curieux c'est que j'ai jamais édité cette partie de lilo.conf, me cantonnant toujours aux 10 dernières lignes.  
 
Donc je ne peux pas dire à qui la faute, mais j'ai l'impression que c'est pas la mienne, pour une fois