bonjours a tous, j'ai un petit problème avec kismet sur mon laptop, plutôt qu'un long discourt mieux vaut un petit log je supose:
Citation :
heartnet:~# kismet
Server options: none
Client options: none
Starting server...
Waiting for server to start before starting UI...
Will drop privs to adamaru (1000) gid 1000
No specific sources given to be enabled, all will be enabled.
Enabling channel hopping.
Enabling channel splitting.
|
et la je perd la connexion wifi donc ssh aime pas du tout ( je me connecte a mon laptop via ssh car la flemme de me déplacer de ma chaise :$ (no comment))
le module madwifi est correctement chargé
Citation :
heartnet:~# lsmod | grep ath
ath_pci 94752 0
ath_rate_sample 14976 1 ath_pci
wlan 195388 6 wlan_tkip,wlan_ccmp,wlan_scan_sta,ath_pci,ath_rate_sample
ath_hal 192336 3 ath_pci,ath_rate_sample
|
du coté de la config de kismet j'ai mis
Citation :
source=madwifi_ag,wifi0,madwifi
|
le problème est le même avec ath1
comme interfaces j'ai
Citation :
heartnet:~# iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
wifi0 no wireless extensions.
Warning: Driver for device ath0 has been compiled with version 21
of Wireless Extension, while this program supports up to version 17.
Some things may be broken...
ath0 IEEE 802.11g ESSID:"akatsuki" Nickname:""
Mode:Managed Frequency:2.462 GHz Access Point: 00:07:CB:56:23:1D
Bit Rate:48 Mb/s Tx-Power:16 dBm Sensitivity=0/3
Retry:off RTS thr:off Fragment thr:off
Encryption key:*faut pas pousser mes mails dans les ordis je cache :p* Security mode:restricted
Power Management:off
Link Quality=13/94 Signal level=-81 dBm Noise level=-94 dBm
Rx invalid nwid:21304 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
ath1 IEEE 802.11g ESSID:"" Nickname:""
Mode:Monitor Frequency:2.467 GHz Access Point: 00:00:00:00:00:00
Bit Rate:0 kb/s Tx-Power:16 dBm Sensitivity=0/3
Retry:off RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=13/94 Signal level=-81 dBm Noise level=-94 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
|
mais avec wifi0 j'obtiens des résultats sous airodump donc je suppose que le mode monitor fonctionne dessus
ma carte est une DWL-G650 sur port pcmcia j'utilise les dernier drivers madwifi trouvé ici: http://snapshots.madwifi.org/madwifi-ng/?C=M;O=D
quand a mon noyaux:
Citation :
Linux blackpearl 2.6.19.1 #5 PREEMPT Thu Dec 28 01:06:16 CET 2006 i686 GNU/Linux
|
je cherche a utiliser kismet pour mettre ma connexion wifi a l'épreuve (je suis un poil parano, d'ailleurs je soupçonne mon chat de tenter de me voler mes mots de passe quand je dors....)
---------------
la voie du click est impénétrable