Driver `eeprom' (should be inserted):
  Detects correctly:
  * Bus `SMBus PIIX4 adapter at fc00'
    Busdriver `i2c-piix4', I2C address 0x50
    Chip `SPD EEPROM' (confidence: 8)
  * Bus `SMBus PIIX4 adapter at fc00'
    Busdriver `i2c-piix4', I2C address 0x51
    Chip `SPD EEPROM' (confidence: 1)
 
  EEPROMs are *NOT* sensors! They are data storage chips commonly
  found on memory modules (SPD), in monitors (EDID), or in some
  laptops, for example.

# sensors-detect revision 4171 (2006-09-24 03:37:01 -0700)
 
This program will help you determine which kernel modules you need
to load to use lm_sensors most effectively. It is generally safe
and recommended to accept the default answers to all questions,
unless you know what you're doing.
 
We can start with probing for (PCI) I2C or SMBus adapters.
Do you want to probe now? (YES/no): YES
Probing for PCI bus adapters...
Use driver `i2c-piix4' for device 0000:00:14.3: Intel 82371AB PIIX4 ACPI
 
We will now try to load each adapter module in turn.
Module `i2c-piix4' already loaded.
If you have undetectable or unsupported adapters, you can have them
scanned by manually loading the modules before running this script.
 
We are now going to do the I2C/SMBus adapter probings. Some chips may
be double detected; we choose the one with the highest confidence
value in that case.
If you found that the adapter hung after probing a certain address,
you can specify that address to remain unprobed.
 
Next adapter: SMBus PIIX4 adapter at fc00
Do you want to scan it? (YES/no/selectively): YES
Client found at address 0x50
Probing for `Analog Devices ADM1033'...                     No
Probing for `Analog Devices ADM1034'...                     No
Probing for `SPD EEPROM'...                                 Success!
    (confidence 8, driver `eeprom')
Probing for `EDID EEPROM'...                                No
Probing for `Maxim MAX6900'...                              No
Client found at address 0x51
Probing for `Analog Devices ADM1033'...                     No
Probing for `Analog Devices ADM1034'...                     No
Probing for `SPD EEPROM'...                                 Success!
    (confidence 1, driver `eeprom')
Client found at address 0x69
 
Some chips are also accessible through the ISA I/O ports. We have to
write to arbitrary I/O ports to probe them. This is usually safe though.
Yes, you do have ISA I/O ports even if you do not have any ISA slots!
Do you want to scan the ISA I/O ports? (YES/no): YES
Probing for `National Semiconductor LM78' at 0x290...       No
Probing for `National Semiconductor LM78-J' at 0x290...     No
Probing for `National Semiconductor LM79' at 0x290...       No
Probing for `Winbond W83781D' at 0x290...                   No
Probing for `Winbond W83782D' at 0x290...                   No
Probing for `Winbond W83627HF' at 0x290...                  No
Probing for `Silicon Integrated Systems SIS5595'...         No
Probing for `VIA VT82C686 Integrated Sensors'...            No
Probing for `VIA VT8231 Integrated Sensors'...              No
Probing for `AMD K8 thermal sensors'...                     No
Probing for `IPMI BMC KCS' at 0xca0...                      No
Probing for `IPMI BMC SMIC' at 0xca8...                     No
 
Some Super I/O chips may also contain sensors. We have to write to
standard I/O ports to probe them. This is usually safe.
Do you want to scan for Super I/O sensors? (YES/no): YES
Probing for Super-I/O at 0x2e/0x2f
Trying family `ITE'...                                      No
Trying family `National Semiconductor'...                   No
Trying family `SMSC'...                                     No
Trying family `VIA/Winbond/Fintek'...                       No
Probing for Super-I/O at 0x4e/0x4f
Trying family `ITE'...                                      No
Trying family `National Semiconductor'...                   No
Trying family `SMSC'...                                     No
Trying family `VIA/Winbond/Fintek'...                       No
 
Now follows a summary of the probes I have just done.
Just press ENTER to continue:
 
Driver `eeprom' (should be inserted):
  Detects correctly:
  * Bus `SMBus PIIX4 adapter at fc00'
    Busdriver `i2c-piix4', I2C address 0x50
    Chip `SPD EEPROM' (confidence: 8)
  * Bus `SMBus PIIX4 adapter at fc00'
    Busdriver `i2c-piix4', I2C address 0x51
    Chip `SPD EEPROM' (confidence: 1)
 
  EEPROMs are *NOT* sensors! They are data storage chips commonly
  found on memory modules (SPD), in monitors (EDID), or in some
  laptops, for example.
 
I will now generate the commands needed to load the required modules.
Just press ENTER to continue:
 
 
If you want to load the modules at startup, generate a config file
below and make sure lm_sensors gets started at boot time; e.g
$ rc-update add lm_sensors default
To make the sensors modules behave correctly, add these lines to
/etc/modules.d/lm_sensors and run modules-update:
 
#----cut here----
# I2C module options
alias char-major-89 i2c-dev
#----cut here----
 
If you have some drivers built into your kernel, the list above will
contain too many modules. Skip the appropriate ones! You really
should try these commands right now to make sure everything is
working properly. Monitoring programs won't work until the needed
modules are loaded.
 
To load everything that is needed, execute the commands below...
 
#----cut here----
# I2C adapter drivers
modprobe i2c-piix4
# Chip drivers
modprobe eeprom
# sleep 2 # optional
/usr/bin/sensors -s # recommended
#----end cut here----
 
Do you want to overwrite /etc/conf.d/lm_sensors? Enter s to specify other file name?
  (yes/NO/s): yes
Done.
 

pentium3 ~ # sensors
w83782d-i2c-0-2d
Adapter: SMBus PIIX4 adapter at 5000
VCore 1:   +2.05 V  (min =  +1.60 V, max =  +2.40 V)
VCore 2:   +1.50 V  (min =  +0.00 V, max =  +4.08 V)
+3.3V:     +3.42 V  (min =  +2.82 V, max =  +3.79 V)
+5V:       +5.13 V  (min =  +5.89 V, max =  +0.54 V)       ALARM
+12V:     +12.46 V  (min = +11.37 V, max =  +5.59 V)       ALARM
-12V:     -12.03 V  (min =  -7.18 V, max =  +4.58 V)       ALARM
-5V:       -5.30 V  (min =  -3.84 V, max =  +0.08 V)       ALARM
V5SB:      +5.13 V  (min =  +5.24 V, max =  +1.94 V)       ALARM
VBat:      +2.90 V  (min =  +4.00 V, max =  +2.91 V)       ALARM
fan1:        0 RPM  (min =    0 RPM, div = 8)
fan2:        0 RPM  (min = 5818 RPM, div = 8)              ALARM
fan3:     5232 RPM  (min = 6553 RPM, div = 2)              ALARM
temp1:       +17°C  (high =   +12°C, hyst =   -17°C)   sensor = thermistor   ALARM
temp2:     +18.0°C  (high =   +80°C, hyst =   +75°C)   sensor = thermistor
temp3:     -48.0°C  (high =   +80°C, hyst =   +75°C)   sensor = thermistor
vid:      +1.650 V  (VRM Version 8.2)
alarms:   Chassis intrusion detection                      ALARM
beep_enable:
          Sound alarm enabled